Sharp AR-M276

AR-M236/M276/M237/M277 SIMULATION 8 - 23
Detection size when 8.5" x 13" document/paper is used.
A4/LT (8.5" x 11") detection enable/disable setup
In the inch series, Letter is detected as A4; in the AB series, A4 is detected as Letter.
Detection size when A4/LT (8.5" x 11") document/paper is used.
Operation/procedure
Select the mode corresponding to the auditor specification mode with
the 10-key.
When "1: VENDOR (Coin vendor mode)" is set, the following three
items of key operation setting are changed.
1) Set the LCD backlight change inhibit to "1: OFF (Enable)."
2) When SIM 26-6 destination setting is set to "0: Japan," duplex copy
inhibit setting must be set to "0: ON (Inhibit)."
3) Set the sort automatic selection to "0: OFF (Disable)."
Operation/procedure
Used to set the count up number (1 or 2) when an A3/WLT paper
passes through.
For the drum counter and the developer counter, double count is
employed unconditionally.
Employed unit Destination Document size
Set value
0
(Invalid)
1
(Valid)
Document Document table/RSPF AB series (Japan) FC (8.5” x 13”)B4 B4
LG (8.5” x 14”)B4 B4
B4 B4 B4
AB series FC (8.5” x 13”)B4FC (8.5” x 13”)
LG (8.5” x 14”)B4FC (8.5” x 13”)
B4 B4 FC (8.5” x 13”)
Inch series FC (8.5” x 13”)LG (8.5” x 14”)FC (8.5” x 13”)
LG (8.5” x 14”)LG (8.5” x 14”)FC (8.5” x 13”)
B4 WLT (11” x 17”)WLT (11” x 17”)
Paper Machine paper feed cassette All destinations – Set with key operations.
Manual paper feed tray Japan (AB series) FC (8.5” x 13”)LG (8.5” x 14”)LG (8.5” x 14”)
LG (8.5” x 14”)LG (8.5” x 14”)LG (8.5” x 14”)
B4 B4 B4
AB series FC (8.5” x 13”)LG (8.5” x 14”)FC (8.5” x 13”)
LG (8.5” x 14”)LG (8.5” x 14”)FC (8.5” x 13”)
B4 B4 B4
Inch series FC (8.5” x 13”)LG (8.5” x 14”)FC (8.5” x 13”)
LG (8.5” x 14”)LG (8.5” x 14”)FC (8.5” x 13”)
B4 B4 B4
Set value Setup Remarks
0 Detection invalid Default
1 Detection valid
Employed unit Destination Document size
Set value
0
(Invalid)
1
(Valid)
Document Document table/RSPF AB series A4 A4 LT (8.5” x 11”)
LT (8.5” x 11”)A4LT (8.5” x 11”)
Inch series A4 LT (8.5” x 11”)A4
LT (8.5” x 11”)LT (8.5” x 11”)A4
Paper Machine paper feed cassette All destinations – Set with key operations.
Manual paper feed tray All destinations – Regardless of the simulation setup.
26-3
Purpose Setting
Function
(Purpose)
Used to set the specifications of the auditor. Setting
must be made depending on the use condition of the
auditor.
Section Auditor
Item Specifications
Item Content
Setting
range
Default
0
P10 Built-in auditor mode 0-2 0
1
VENDOR Coin vendor mode
2
OTHER Others
26-5
Purpose Setting
Function
(Purpose)
Used to set the count mode of the total counter and the
maintenance counter.
Item Specifications Counter