AR-M236/M276/M237/M277 SIMULATION 8 - 38
Operation/procedure
1. Touch the item to be adjusted.
The item and the currently set value are highlighted.
2. Enter the adjustment value with the 10-key and press the [P] key.,
The display goes to the copy menu.
When the [START] key is pressed, the display goes to the copying
state and print is started.
(When the [P] key is pressed: Copy menu)
3. Select the paper feed tray and the print density.
Enter the exposure level with the 10-key.
4. Press the [START] key.
Copying is started.
Note: When this simulation is canceled, the display is shifted to the ini-
tial menu, but the machine is not reset.
(Adjustment procedure)
1. Note down the adjustment value of SIM 50-5 (Items 1, 2, 3, 4), and
change the value to 99.
2. Set SIM 50-1 (Items 2, 3, 4, 5) to 1. (By setting to 1, there is no
void.)
3. Place a chart with a clear lead edge (or a ruler) on the OC docu-
ment table.
4. Use SIM 50-1 (Item 1) to execute test print. Check the print out and
adjust so that the lead edge image is printed. (1 - 99: About
0.127mm/Step)
5. Reset the adjustment values of SIM 50-5 (Items 1, 2, 3, 4) to the
original values, and execute test print. Check the print out and
adjust so that the lead edge image is printed on the lead edge of
paper. (1 - 99: About 0.127mm/Step).
6. Adjust SIM 50-1 (Items 2, 3, 4, 5) so that the lead edge void on the
print out is the specified value. (1 - 99: About 0.127mm/Step)
7. Similar to procedure 6, adjust SIM 50-1 (Item 6, 7) so that the rear
edge void is the specified value. (1 - 99: About 0.127mm/Step)
8. Similar to procedure 6, adjust SIM 50-1 (Item 8, 9) so that the left
edge void is the specified value. (1 - 99: About 0.127mm/Step)
9. Make an enlargement copy (400%), and check that there is no
shade of the cabinet printed at the lead edge.
10. If there is a shade printed at the lead edge in procedure 9, adjust
SIM 50-1 (Item 10). (1 - 5: About 0.677mm)
* If there is no problem, set to 2.
Operation/procedure
1. Touch the item to be adjusted.
The item and the currently set value are highlighted.
2. Enter the adjustment value with the 10-key and press the [P] key.,
The display goes to the copy menu.
When the [START] key is pressed, the display goes to the copying
state and print is started.
(When the [P] key is pressed: Copy menu)
3. Select the paper feed tray and the print density.
Enter the exposure level with the 10-key.
4. Press the [START] key.
Copying is started.
Note: When this simulation is canceled, the display is shifted to the ini-
tial menu, but the machine is not reset.
Operation/procedure
1. Touch the item to be adjusted.
The item and the currently set value are highlighted.
2. Enter the adjustment value with the 10-key and press the [P] key.,
The display goes to the copy menu.
When the [START] key is pressed, the display goes to the copying
state and print is started.
(When the [P] key is pressed: Copy menu)
3. Select the paper feed tray and the print density.
Enter the exposure level with the 10-key.
4. Press the [START] key.
Copying is started.
Note: When this simulation is canceled, the display is shifted to the ini-
tial menu, but the machine is not reset.
Item Content
Setting
range
Default
1
RRC-A
Original scan start position
adjustment
Lead edge position
adjustment value (OC)
1-99 43
2
DEN-A
Lead edge cancel
adjustment (Main cassette)
1-99 18
3
DEN-A-MANUAL
Lead edge cancel
adjustment (Manual feed
cassette)
1-99 18
4
DEN-A -OPTION
Lead edge cancel
adjustment (Option cassette)
1-99 18
5
DEN-A -DUPLEX
Lead edge cancel
adjustment (back of the
machine)
1-99 18
6
DEN-B
Rear edge void adjustment 1-99 30
7
DEN-B-DUP
Rear edge void adjustment
(Duplex)
1-99 50
8
SIDE VOID
Left edge void adjustment
(First print surface)
1-99 18
9
SIDE VOID-DUP
Left edge void adjustment
(Duplex)
1-99 18
10
LOSS(OC)
Image loss amount
adjustment (Lead edge
image loss set value) (OC)
1-5 3
50-5
Purpose Adjustment
Function
(Purpose)
Used to adjust the print image position (top margin) on
the print paper in the print mode.
Item Picture quality Print area
Item Content Setting range Default
1TRAY1
1st cassette 0-99 53
2OPTION
Option cassette 1-99
3MANUAL
Manual feed
4DUPLEX
Back print
50-6
Purpose Adjustment
Function
(Purpose)
Used to adjust the print image position (top margin) on
print paper in the copy mode. (SPF/RSPF)
Item Picture quality Image position
To Next Page
Loading...
