Siemens 353 - Page 6

Contents UM353-1B
iv April 2012
7.4.2 Analog Signal Input Wiring (4-20 mA, 1-5 Vdc, and mV) ................................................................ 7-10
7.4.3 Analog Output Wiring (4-20 mA, 1-5 Vdc) ....................................................................................... 7-12
7.4.4 Digital Input and Output Wiring......................................................................................................... 7-13
7.4.5 Thermocouple Input Wiring................................................................................................................ 7-15
7.4.6 RTD Input Wiring............................................................................................................................... 7-16
7.4.7 Ohms and Slidewire Input Wiring ...................................................................................................... 7-17
7.4.8 Relay Output Wiring........................................................................................................................... 7-17
7.4.9 Modbus Wiring ................................................................................................................................... 7-18
7.4.10 Ethernet Wiring................................................................................................................................. 7-18
7.4.11 Wiring to a Siemens SIREC D Recorder .......................................................................................... 7-20
7.4.12 Power Wiring .................................................................................................................................... 7-20
7.5 FACTORY CALIBRATION....................................................................................................................... 7-22
8.0 LOCAL FACEPLATE OPERATION............................................................................................................. 8-1
8.1 NORMAL OPERATION MODE.................................................................................................................. 8-1
8.2 CONFIGURATION MODE.......................................................................................................................... 8-3
8.3 AUTOTUNE PROCEDURE......................................................................................................................... 8-4
9.0 CONTROLLER AND SYSTEM TEST........................................................................................................... 9-1
9.1 CONTROLLER CONFIGURATION AND TEST ....................................................................................... 9-1
9.1.1 Connections and Power......................................................................................................................... 9-1
9.1.2 Configuration ........................................................................................................................................ 9-2
9.1.3 Input/Output.......................................................................................................................................... 9-2
9.1.4 Auto/Manual ......................................................................................................................................... 9-2
9.1.5 Modifying an FCO................................................................................................................................ 9-2
9.1.6 Alarms................................................................................................................................................... 9-4
9.1.7 TAG ...................................................................................................................................................... 9-5
9.1.8 QUICK.................................................................................................................................................. 9-5
9.1.9 TUNE.................................................................................................................................................... 9-6
9.1.10 View mode .......................................................................................................................................... 9-7
9.2 SYSTEM CHECKOUT................................................................................................................................. 9-7
10.0 MAINTENANCE .......................................................................................................................................... 10-1
10.1 TOOLS AND TEST EQUIPMENT .......................................................................................................... 10-1
10.2 PREVENTIVE MAINTENANCE ............................................................................................................ 10-2
10.2.1 Environmental Considerations.......................................................................................................... 10-2
10.2.2 Visual Inspection............................................................................................................................... 10-2
10.2.3 Cleaning ............................................................................................................................................ 10-2
10.2.4 Circuit Board Handling..................................................................................................................... 10-3
10.3 TROUBLESHOOTING............................................................................................................................. 10-4
10.4 ERROR CODES........................................................................................................................................ 10-6
10.4.1 Off-Line Error Codes........................................................................................................................ 10-6
10.4.2 On-Line Error Codes and Status Codes ............................................................................................ 10-7
10.4.3 MultiMediaCard Error Codes ........................................................................................................... 10-9
10.5 ASSEMBLY REPLACEMENT ................................................................................................................ 10-9
10.5.1 Fuse................................................................................................................................................... 10-9
10.5.2 Display Assembly ........................................................................................................................... 10-10
10.5.3 MPU Controller Board.................................................................................................................... 10-12
10.5.4 I/O Expander Board ........................................................................................................................ 10-12
10.5.5 Ethernet Cable................................................................................................................................. 10-13
10.6 MULTIMEDIACARD – FORMATTING AND FILE NAMES ............................................................ 10-14
11.0 CALIBRATION ............................................................................................................................................ 11-1
11.1 ANALOG INPUT (AIN1-4)...................................................................................................................... 11-2
11.2 ANALOG OUTPUT (AOUT1-3).............................................................................................................. 11-3
11.3 UNIVERSAL ANALOG INPUTS (AINU1 AND AINU2)...................................................................... 11-3
12.0 CIRCUIT DESCRIPTION ........................................................................................................................... 12-1