Siemens FIREFINDER-XLS User Manual

DESCRIPTION 1-3
CHAPTER 1 | FIREFINDER-XLS INSTALLATION, OPERATION AND MAINTENANCE MANUAL
CONFIGURATION The table below presents the minimum configuration necessary to meet NFPA 72
Local, Municipal Tie, Remote Station, Proprietary and Central Station, UL 1076, NFPA
13 and 2001, ULC S527, UL2572, and ULC S576.
MINIMUM FIREFINDER-XLS CONFIGURATION TO MEET NFPA 72, UL1076, NFPA 13, 2001, ULC S527, UL2572, AND ULC S576
eludoMnoitpircseD
ytitnauQmuminiMAPFN
ecioV
dnaSU
adanaC
adanaC
yrateirporPlacoLyrailixuA
etomeR
noitatS
lartneC
noitatS
9
LU
6701
01,1
ro31
1002
LU
-/2752
CLU
675S
CLU
725S
3-IMP/2-IMP/IMP
2
ecafretnIenihcaMnosreP11111111§1
21-CSPylppuSrewoP11111111§1
BTPdraoBnoitanimreTrewoP11111111§1
A04-PST/1-LAP/MPRecafretnIretnirPetomeR1X X X
X 1X X§ X
5-CCegaCdraC11111111§1
A4-CIZ
3
draCgnitacidnIenoZ1
21
1
21
11
4
1
31
1
21
1
11
1
21
§1
21
C2/B8-CIZ
/draCgnitacidnIenoZ
tnemecnahnEoiduAlennahC2
1
21
1
21
X X X 1
21
X 1
21
§1
21
6B-PCI/PCHtnioPlortnoCtnegilletnI1
21
1
21
X X X 1
21
X 1
21
§1
21
CLDdraCpooLeciveD1
51
1
51
1
51
1
51
1
51
1
51
1
51
1§ 1
51
CLMdraCeniLLXM1
51
1
51
1
51
1
51
1
51
1
51
1
51
X§ 1
51
—seirettaB
7,6,5
11111111§1
1-WSTHhctiwSrepmaTX X X X X 1X X§ X
C-CINdraCecafretnIkrowteNX
8
X
8
X
8
X
8
X
8
X
8
X
8
X
8
§X
8
TEN-CADTEND-draCoiduAlatigiDX X X X X X X 11 X
BPLdraoBegaPlacoLX X X X X X X 11 X
MVLeludoMecioVeviLX X X X X X X 11 X
04-CAZdraCreifilp
mAenoZX X X X X X X 1
61
1
61
X
081-MAZeludoMreifilpmAenoZX X X X X X X 1
61
1
61
X
1U-5102ACF/TCADM
71
moCmralAlatigiDtnioPitluM1
41
X X 1
31
1
31
X X X§ X
.ytitnauqmuminimadanaCroAPFNrehtierofnmulocnoitacifissalcmetsysotrefeR=§deriuqertoN=X
1 Only HTRI-S, HTRI-D, HTRI-R (DLC); and TRI-60, TRI-S, TRI-B6, TRI-60R, TRI-R, TRI-B6R, TRI-60D, TRI-D and TRI-B6D
(MLC) can be used as security initiating devices.
2 The PMI/PMI-2/PMI-3 must be programmed by the Zeus programming tool for all System configurations (See the
Zeus Quick Start Manual, P/N 315-033875).
3 Caution: Disarm all ZIC-4A circuits configured for Releasing Device Service prior to system maintenance.
4 One ZIC-4A circuit must be configured for alarm transmission. In addition, depending on the local authority having
jurisdiction, additional circuits may be required for Supervisory or Trouble transmission.
5 Reference the System Label, P/N 575-234411, for battery maintenance and replacement schedule.
6 The batteries available are BP-61, BTX-1, BTX-2 and BTX-3. The BP-61 is a 24V 15 AH battery. The BTX-1 batteries are
a pair of 12V, 33 AH batteries. The BTX-2 are a pair of 12V, 75 AH batteries. The BTX-3 are a pair of 12V, 100 AH
batteries. Actual battery size depends on System configuration.
7 See the PSC-12 Installation Instructions, P/N 315-033060, for Battery Calculations.
8 For multi-enclosure systems, one NIC-C is required in each enclosure.
9 For Central Station, see Appendix E.
10 UL 1076 requires a Model HTSW-1 Tamper Switch and an RPM Remote Printer Module or a TSP-40A Logging Printer.
11 Refer to the ZIC-4A Installation Instructions (P/N 315-033050) for programming.
12 At least one ZIC-4A / ZIC-8B / HCP / ICP-B6 must be installed.
13 Use either the ZIC-4A, MDACT, or FCA2015-U1 depending on the communication circuit type.
14 Refer to the MDACT Installation Instructions, P/N 315-099351, or FCA2015-U1 Installation Instructions, Document ID
A6V10334254, for compatible head-end equipment. Only required for DAC (Digital Alarm Communicator) Type Signaling.
15 One DLC or one MLC is required.
16 At least one ZAC-40/ZAM-180 must be installed.
17 The FCA2015-U1 requires the XDACT-ASSY mounting bracket, Document ID A6V10807278.

Siemens FIREFINDER-XLS Specifications

General

Brand	Siemens
Model	FIREFINDER-XLS
Category	Control Panel
Language	English