Siemens PUMA V8300/M - (5) Tool Setting

161 pages

To Next Page

To Previous Page

PROGRAMMING | 109

➀ Tool load monitoring Function ON(Recording dimension, Recording Current, Monitoring)

➁ Real cutting program

➂ Tool load monitoring Function OFF.

(5) Tool Setting

This setting can be enabled in AUTO mode only.

This setting specifies tool information and distance information.

Main Page

Table of Contents5
Part 1 MAIN OPERATION PANEL9
Power Switches9
Layout of Power Switches9
Operation of Power Switches9
Main Operation Panel10
Layout of Operation Panel10
Operation Panel Switches12
Key Selector Switch23
Optional Function Switch24
Foot Switch Operation25
LED Display25
Other Switches26
Part 2 OPERATION27
Power Supply & Break27
Power Supply27
Emergency Stop & Machine Ready29
Emergency Stop29
Machine Ready30
Operation Mode Selection32
Operation Mode32
Axis Feed Operation34
Jog Traverse35
Rapid Traverse During Jog Traversing37
Handle Feed38
Manual REF. Point Return40
C-AXIS Mode43
C-Axis Clamp/Unclamp Operation44
Axis Traverse and Restrictions in C-Axis Clamp Status44
Spindle Axis Mode Command in Auto Mode45
Spindle46
Spindle Operation46
Spindle Selection47
Spindle Rotation and Operation in Manual Mode48
Spindle Rotation Command in Auto Mode49
Spindle Rotation Condition51
Spindle Override Operation52
Spindle Gear Switching53
Chucking Operation54
Chuck Operation55
Restrictions in Machine Operation According to the Status of Chucking56
Chuck Clamp/Unclamp Check57
Chuck Clamp/Unclamp Operation60
Dual Chucking (Option)62
Chucking Operation on Spindle Rotating64
Tool Post65
The Movement of Tool Post65
The Operation of Tool Post66
Coolant Operation69
Connecting Coolant Motor and Peripheral Device69
Standard Coolant Operation69
Optional Coolant71
Mutual Operation between Standard and Optional Coolant71
Cool Jet Coolant Operation72
Coolant Flushing73
Quick Tool Presetter (Option)74
Automatic Type Quick Tool Presetter Operation75
Manual Type Quick Tool Presetter Operation77
Measuring a Tool with a Tool Probe78
Calibrating the Tool Probe80
Air Blow (Option)81
Air Blow Operation81
Signal Tower (Option)83
The Machine Status According to the Light Color of Signal Tower83
Parts Count84
Parts Count Function84
Auto Power off(Option)85
The Sequence of Auto Power off85
Auto Door(Option)86
Auto Door Operation86
Chip Conveyor(Option)87
Chip Conveyor Operation87
Part 3 PROGRAMMING89
M Function89
M Code List89
Tool Function (T Function)107
Tool Change with T Command107
Tool Offsets108
Spindle Function (S Function)111
Spindle Speed(S), Direction of Spindle Rotation(M3,M4,M5)111
Tool Load Monitoring Function (Option)112
Introduction112
Basics Operation113
Convenience Function124
Part 4 MAINTENANCE129
Enter the Final End User Data (EUNA)129
This Is How You Generate the Machine Logbook129
This Is How You Make a New Entry in the Logbook131
This Is How You Save the Machine Identity132
This Is How You Send the End Use Final Destination Data134
Easy Explanation of RSC(Repair Service Contract) Procedure136
NC & PLC Initialization141
Referencing with Absolute Value Encoders141
Adjustment141
Adjustment Methods141
Readjustment141
Sequence142
PLC Monitoring (Valid for Only S828)143
Turret Service Mode145
Turret Service Screen145
Operation in Turret Service Mode146
Service Planner147
Acknowledging a Maintenance Task148
Easy Extend Function.(Only Available 828D)149
Easy Extend Screen149
Machine Data to Enable Machine Options154

Siemens PUMA V8300/M - (5) Tool Setting

Table of Contents

Related product manuals