Siemens SINUMERIK 808D Commissioning Manual

Commissioning Manual
01/2017
9
15.1 SINUMERIK 808D/SINUMERIK 808D ADVANCED ............................................................................ 383
15.2 Servo drives ........................................................................................................................................ 384
15.2.1 SINAMICS V70 feed drives ................................................................................................................. 384
15.2.2 SINAMICS V70 spindle drives ............................................................................................................. 386
15.2.3 SINAMICS V60 servo drives ............................................................................................................... 388
15.3 Servo motors ....................................................................................................................................... 390
15.3.1 SIMOTICS S-1FL6 feed motors .......................................................................................................... 390
15.3.2 SIMOTICS S-1FL5 servo motors ......................................................................................................... 394
15.3.3 SIMOTICS M-1PH1 main motors ........................................................................................................ 396
15.4 Cables ................................................................................................................................................. 408
15.4.1 Drive Bus cable for the SINUMERIK 808D ADVANCED ..................................................................... 408
15.4.2 Cables for the SINAMICS V70 servo system ...................................................................................... 408
15.4.3 Cables for the SINAMICS V60 servo system ...................................................................................... 409
15.5 Transformers for the SINAMICS V60 servo system ............................................................................ 410
15.6 Address of CE-authorized manufacturer ............................................................................................. 411
16 Parameter list ..................................................................................................................................................... 411
16.1 Basic machine data ............................................................................................................................. 411
16.2 SINAMICS V70 parameters ................................................................................................................. 416
16.2.1 V70 parameters on BOP ..................................................................................................................... 418
16.2.2 Drive basic list on HMI ......................................................................................................................... 425
16.3 SINAMICS V60 parameters ................................................................................................................. 427
17 PLC user interface .............................................................................................................................................. 431
17.1 Signals from/to the MCP ...................................................................................................................... 431
17.2 Reading/Writing NC data ..................................................................................................................... 433
17.2.1 Reading/writing NC data: Job .............................................................................................................. 433
17.2.2 Reading/writing NC data: Result ......................................................................................................... 433
17.3 PI Service ............................................................................................................................................ 434
17.3.1 PI service: Job ..................................................................................................................................... 434
17.3.2 PI service: Result ................................................................................................................................ 434
17.4 Retentive data area ............................................................................................................................. 434
17.5 User Alarms ......................................................................................................................................... 435
17.5.1 User alarms: Activating ........................................................................................................................ 435
17.5.2 Variables for user alarms ..................................................................................................................... 435
17.5.3 Active alarm response ......................................................................................................................... 436
17.5.4 Alarm acknowledgement ..................................................................................................................... 436
17.6 Signals from/to HMI ............................................................................................................................. 436
17.6.1 Program control signals from the HMI (retentive area) ........................................................................ 436
17.6.2 Program selection from PLC (retentive area) ...................................................................................... 437
17.6.3 Checkback signal: Program selection from HMI (retentive area) ......................................................... 437
17.6.4 Signals from HMI ................................................................................................................................. 437
17.6.5 Signals from PLC ................................................................................................................................ 437
17.6.6 Signals to maintenance planners ........................................................................................................ 438
17.6.7 Signals from maintenance planners .................................................................................................... 438
17.6.8 Signals from operator panel (retentive area) ....................................................................................... 439
17.6.9 General selection/status signals from HMI (retentive area) ................................................................. 439
17.6.10 General selection/status signals to HMI (retentive area) ..................................................................... 439
17.7 Auxiliary functions transfer from NC channel ....................................................................................... 440
17.7.1 Overview ............................................................................................................................................. 440
17.7.2 Decoded M signals (M0 to M99) .......................................................................................................... 441
17.7.3 Transferred T functions ....................................................................................................................... 441
17.7.4 Transferred M functions ....................................................................................................................... 441
17.7.5 Transferred S functions ....................................................................................................................... 442
17.7.6 Transferred D functions ....................................................................................................................... 442
17.7.7 Transferred H functions ....................................................................................................................... 442
17.8 NCK signals ......................................................................................................................................... 442
17.8.1 General signals to NCK ....................................................................................................................... 442

Siemens SINUMERIK 808D Specifications

General

Brand	Siemens
Model	SINUMERIK 808D
Category	Control Unit
Language	English