11.90 6 Data Interfaces
6.4 Device connection data
Siemens page printer PT80
Cable Order No.: 6FC9 340-8C
RS232C (V.24 )
6FC9 340-8T
(20mA)
Device data
Transfer rate: 300 baud
Character format: 1 Start bit
8 Data bits
2 Stop bits
Order No. for PT80 to SINUMERIK
specification:
Type RS232C (V.24) : L22751-A80-
D442
(Interface module
STT104)
Type 20mA : L22751-A80-D441
(Interface module
STT104+LAT101)
Additional cable
for terminal
connection:
6FC9340-4KA
An NC-controlled read operation (start
/stop) is possible on the device with a
20mA interface.
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Siemens printer PT88
Cable Order No.: 6FC9 340-8D.
Device data
Interface adaptation SAP-S1
(RS232C (V.24))
Setting of the operating mode
switches
Switch S1
123456
ON ON ON OFF OFF OFF
(with this setting, the printer has a
transfer rate of 9600 baud)
Switch S2
123456
OFF ON OFF ON OFF ON
(this setting denotes:
BUSY (X2.10) line is switched to BUSY
(X1.25) line, with negative potential)
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
© Siemens AG 1990 All Rights Reserved 6ZB5 410-0EP02 6-7
SINUMERIK 810T, GA3 (BN)
To Next Page
Loading...
