Siemens Sinumerik 810T User Manual

2 Operation 11.90
2.3.4 ”Reset” with change of operating mode
2.3.4 ”Reset” with change of operating mode
• When changing from one selected operating mode to another (see Handling, Section
2.3.3.1 and / or Section 2.3.3.2), a ” RESET” can be generated by the control.
• The ”RESET” generated by the control when changing has the same effect as if the
”RESET” key had been operated (Section 2.1.1.6 or 2.1.2.1).
• The generation of a ”RESET” depends on the modes switched.
Generation of ”RESET” with change of operating mode
(
+ ... Reset, o ... No Reset)
MDI AUTO
MATIC
PRESET JOG REPOS
AUTO-
MATIC
INC
...
REF-
POINT
PRESET
MDI AUTO-
MATIC
JOG
REPOS
AUTO-
MATIC
INC
...
REF-
POINT
a a a a a a a a a a a a a a a
a
a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a
a
a a a a a a a a a a a a a a a
a a a a a a a a a a a a a a a
a
a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a
a
a a a a a a a a a a a a a a a
a a a a a a a a a a a a a a
a
a a a a a a a a a a a a
a
a
a a a a a a a a a a a a
a
a
a a a a a a a a a a a a
a
a
a a a a a a a a a a a a
a
a
a a a a a a a a a a a a
a
a
a a a a a a a a a a a a
a
a
a a a a a a a a a a a a
a
a a a a a a a a a a a a a a
a a a a a a a a a a a a a a a
a a a a a a a a a a a a a a a
a a a a a a a a a a a a a a a
a a a a a a a a a a a a a a a
a a a a a a a a a a a a a a a
a a a a a a a a a a a a a a a
a a a a a a a a a a a a a a a
a a a a a a a a a a a a a a a
a a a a a a a a a a a a a a a
a a a a a a a a a a a a a a a
a a a a a a a a a a a a a a a
a
a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a
a
a a a a a a a a a a a a a a a
a a a a a a a a a a a a a a a
a
a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a
a
a a a a a a a a a a a a a a a
a a a a a a a a a a a a a a a
a
a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a
a
a a a a a a a a a a a a a a a
+
+
+
+
+
+
+
+
+
+ +
+
+
+
+
o
o
o
+
+
o
o
o
+ +
o
+
+ + +
+
+
+
+
+
++
o o
o
o
o
Examples:
1) When changing from ”AUTOMATIC” to ”JOG” mode, no ”RESET” is generated by the
control!
2) When changing from ”JOG” to ”REFPOINT” mode, a ”RESET” is generated by the
control!
2-42
© Siemens AG 1990 All Rights Reserved 6ZB5 410-0EP02
SINUMERIK 810T, GA3 (BN)

Siemens Sinumerik 810T Specifications

General

Brand	Siemens
Model	Sinumerik 810T
Category	Network Hardware
Language	English