Siemens SINUMERIK 880 GA2

08.96 1 Introduction
1.4.2 Workpiece probe in the TOA memory for turning machines
Fig. 1.11 Workpiece probe type 7 in the TOA memory for turning machines
a a a a a a a a a a a a a a a a a
a
a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a
a
a a a a a a a a a a a a a a a a a
F
a a a a a a a a a
a
a a a a a a a
a
a
a a a a a a a
a
a
a a a a a a a
a
a
a a a a a a a
a
a
a a a a a a a
a
a
a a a a a a a
a
a
a a a a a a a
a
a
a a a a a a a
a
a
a a a a a a a
a
a
a a a a a a a
a
a
a a a a a a a
a
a
a a a a a a a
a
a
a a a a a a a
a
a
a a a a a a a
a
a
a a a a a a a
a
a
a a a a a a a
a
a
a a a a a a a
a
a
a a a a a a a
a
a
a a a a a a a
a
a
a a a a a a a
a
a a a a a a a a a
L2
L1
r
Dn
P0P0
P1
P2
P3
P4
P5
P6
P7
P8
P9
P0
7
L1
L2
r
0
0
0
0
0
Tool Number
L1 Geometry
L2 Geometry
Tool type
Diameter/radius
L1 Wear
L2 Wear
Diameter/radius
Base (add. TO)
Base (add. TO)
Type 7
Fig. 1.12 Workpiece probe type 8 (6) in the TOA memory for turning machines
(type in parentheses = in front of turning centre)
a a a a a a a a
a
a a a a a a
a
a
a a a a a a
a
a
a a a a a a
a
a
a a a a a a
a
a
a a a a a a
a
a
a a a a a a
a
a
a a a a a a
a
a
a a a a a a
a
a
a a a a a a
a
a
a a a a a a
a
a
a a a a a a
a
a
a a a a a a
a
a
a a a a a a
a
a
a a a a a a
a
a
a a a a a a
a
a
a a a a a a
a
a a a a a a a a
L2
r
a a a a a a a a a a a a a a a a a a a a a a a
a a a a a a a a a a a a a a a a a a a a a a a
a a a a a a a a a a a a a a a a a a a a a a a
a a a a a a a a a a a a a a a a a a a a a a a
a a a a a a a a a a a a a a a a a a a a a a a
a a a a a a a a a a a a a a a a a a a a a a a
a a a a a a a a a a a a a a a a a a a a a a a
a a a a a a a a a a a a a a a a a a a a a a a
a a a a a a a a a a a a a a a a a a a a a a a
a a a a a a a a a a a a a a a a a a a a a a a
a a a a a a a a a a a a a a a a a a a a a a a
a a a a a a a a a a a a a a a a a a a a a a a
a a a a a a a a a a a a a a a a a a a a a a a
a a a a a a a a a a a a a a a a a a a a a a a
a a a a a a a a a a a a a a a a a a a a a a a
a a a a a a a a a a a a a a a a a a a a a a a
a a a a a a a a a a a a a a a a a a a a a a a
a a a a a a a a a a a a a a a a a a a a a a a
a a a a a a a a a a a a a a a a a a a a a a a
a a a a a a a a a a a a a a a a a a a a a a a
a a a a a a a a a a a a a a a a a a a a a a a
L1
F
Dn
P0P0
P1
P2
P3
P4
P5
P6
P7
P8
P9
P0
8
L1
L2
r
0
0
0
0
0
Tool number
L1 Geometry
L2 Geometry
Tool type
Diameter/radius
L1 Wear
L2 Wear
Diameter/radius
Base (add. TO)
Base (add. TO)
Type 8 (6)
© Siemens AG 1990 All Rights Reserved 6FC5197- AB70 1–11
SINUMERIK 840/850/880 (BN)