Siemens TUTORbit POL895 User Manual

85
TUTORBIT
COSMOGAS
Continued on the next page
6 - USE
Reduced Heating Set Band settings for QMX3 Room sensor
Installer 8...40 Value
Heating Protection Set Band settings for QMX3 Room sensor
Installer -2...10 Value
Comfort Setpoint Cooling Band settings for QMX3 Room sensor
Installer 8...40 Value
Cooling Precomfort Set Band settings for QMX3 Room sensor
Installer 8...40 Value
Reduced Cooling Set Band settings for QMX3 Room sensor
Installer 8...40 Value
Cooling Protection Set Band settings for QMX3 Room sensor
Installer 10...20 Value
Hysteresis Activation or deactivation hysteresis of the heating / cooling demand
Installer 0...2 0.5°C
Heat Pump
Installer
Shutdown Differential HP Shutdown Differential HP in cooling if the system does not absorb enough cold
Installer 0...100 3°C
CutOff Temp. Outdoor shutdown temperature of the HP in hot because it no longer performs well
Installer 0...10 5°C
Temp. Cutoff Hyst. Hysteresis on the cascade setpoint to switch off the boiler and leave the HP on
Installer 0...3 1°C
Saturation time Time of the HP in HEAT to reach the setpoint. If it does not succeed in this time, the boiler switches on
Installer 0...120 120°C
Saturation hysteresis Hysteresis on saturation
Installer 0...10 1°C
Defrost In Time Time during which the temperature drop “Differ. defrost In” due to defrosting is monitored
Installer 0...90 5min
Differ. defrost In Temperature drop due to defrost
Installer 0...20 5°C
Defrost Out Time Time during which the temperature rise “Differ. defrost Out” due to defrosting is monitored
Installer 0...90 5min
Differ. defrost Out Temperature rise due to defrost
Installer 0...20 5°C
Incr. Temp. CutOff Increase of the Cutoff temperature at each defrost
Installer 0...120 1°C
Decreasing time CutOff Time after which I return to lower the Cutoff temperature
Installer 0...360 X min
DHW CutOff Temp. DHW cutoff outdoor temperature
Installer 0...50 5°C
DHW Cutoff Hyst. Temp. Hysteresis on the outdoor temperature of the DHW cutoff
Installer 0...3 1°C
Maximum time DHW Maximum time to tank load then the boiler is switched on
Installer 0...300 X min
Post DHW Circulation Post circulation which is activated after the HP has nished a DHW cycle, before diverting to the boiler
Installer 0...300 60s
System state System state parameters (read-only)
Installer
System N/A
Installer Value Value
Request DHW or Heating request
Installer Value Value
Sensors state State of the temperature measurement sensors
Installer
Actual outdoor temp Outdoor temperature
Installer Value Value
Water heater t. General cascade temperature
Installer Value Value
Zone1 supply t. Circuit 1 supply temperature; visible only with 3 way valve so Conguration>Zones>3 way valve n>Type Zone=Mix
Installer Value Value
Zone2 supply t. Circuit 2 supply temperature; visible only with 3 way valve so Conguration>Zones>3 way valve n>Type Zone=Mix
Installer Value Value
Zone3 supply t. Circuit 3 supply temperature; visible only with 3 way valve so Conguration>Zones>3 way valve n>Type Zone=Mix
Installer Value Value
Zone4 supply t. Circuit 4 supply temperature; visible only with 3 way valve so Conguration>Zones>3 way valve n>Type Zone=Mix
Installer Value Value
Zone5 supply t. Circuit 5 supply temperature; visible only with 3 way valve so Conguration>Zones>3 way valve n>Type Zone=Mix
Installer Value Value
DHW tank sens Hot water tank temperature
Installer Value Value
Solar hot water tank T. Solar hot water tank temperature
Installer Value Value
Solar tank sens Solar panel tank temperature
Installer Value Value
Solar panel temp Solar panel temperature
Installer Value Value

Siemens TUTORbit POL895 Specifications

General

Brand	Siemens
Model	TUTORbit POL895
Category	Controller
Language	English