Silvercrest SKMC 1200 B2 - Troubleshooting and Specifications; Troubleshooting Common Issues

31
GB
16.9 Change menu language
If desired, you can change the language for the menus.
1. Tap the button on the screen.
2. If required, tap .
3. Slide the menu up with one finger and then press the
CHANGE field in the Language row.
4. Tap the field of the desired language and confirm the
selection.
The screen goes dark and then appears after a few
seconds with the new languages.
17. Cleaning and servicing the
device
DANGER! Risk of electric shock!
~ Disconnect the mains plug15 from the mains socket
before any cleaning.
~ Never immerse the base unit13 in water.
DANGER! Risk of injury from cutting!
~ Please remember that the blades of the blade assem-
bly18 are very sharp. Never touch the blades with
your bare hands in order to avoid cuts.
~ Before removing the blade assembly18, rinse the
blender jug5 with water and remove scraps of food
from the blades so that the blade assembly18 can be
removed safely.
~ When washing manually, the water should be suffi-
ciently clear so that you can see the blade assem-
bly18 easily to avoid injuries caused by the very
sharp blades.
CAUTION:
~ Never use any abrasive, corrosive or scouring clean-
ing agents. These might damage the device.
NOTE: certain foods or spices (e.g. curry) may discolour
the plastic. This is not a device error and is harmless to
health.
17.1 Cleaning the base unit
1. Clean the base unit13 with a damp cloth. You can
also use a little washing-up liquid.
2. Then wipe off with a clean, moist, light cloth with
clean water.
3. Do not use the base unit13 until it is completely dry
again.
4. The screen can also be cleaned with a lens cleaning
cloth or special cleaning agents for monitors.
17.2 Cleaning in the dishwasher
The following parts are dishwasher-safe:
-Blender jug5
-Measuring beaker24
- Lid for blender jug23
- Seal for blender jug22
- Blade assembly18
- Seal for blade assembly17
-Cooking pot19
- Mixer attachment20
- Spatula21
- Steamer attachment, deep3
- Seal for the steamer attachment4
- Steamer attachment, shallow2
- Lid for the steamer attachments1
The following parts must never be cleaned in a dishwasher:
-Base unit13
NOTE: before cleaning the blender jug5 in the dishwash-
er, always remove the blade assembly18.
17.3 Cleaning the accessories
1. Rinse the blender jug5 with warm water and dump
the water.
2. Remove the blade assembly18 (see “Using and re-
moving the blade assembly” on page 12) and take
the seal17 off (see “Cleaning, checking and replac-
ing seals” on page 31).
3. Clean all accessories by hand in a sink with dishwa-
ter or in the dishwasher.
4. When cleaning by hand, rinse all parts with clean
water.
5. Allow the parts to dry completely before using them
again.
6. Before using the device again, reinsert the blade as-
sembly18 in the blender jug5.
17.4 Cleaning, checking and
replacing seals
Remove seals17,22 and4 for cleaning and check them
for damage. Pay attention to changes (e.g. porous materi-
al or tears).
- The removed seals17,22 and4 can be cleaned in
the dishwasher.
- Damaged seals17,22 and4 must be replaced with
new ones. You can reorder new seals (see “How to or-
der accessories” on page 34).
CAUTION:
~ Prior to the next use, damaged seals17,22 and4
must be inserted again or replaced with new ones. An
operation without seals17,22 and4 in place is not
permitted.
__317552_MC-Connect_GB.book Seite 31 Donnerstag, 21. März 2019 10:53 10