Press the START/PAUSE button to store the setting you
have chosen.
If you do not press WATER TEMP or START/PAUSE within
5 seconds of the last press or you press any other button, the
machine will exit the adjusting mode. In this case the settings will
not have been changed.
To switch off the end of program Beep
The washing machine is factory set to ‘beep’ when your wash
is finished. It will also ‘beep’ when the machine has paused at
completion of the Drip Dry wash program, to alert you to
remove the drip dry clothes from the washbowl.
To change the ‘beeping’ selection, proceed as follows:
1. Press and hold the WASH CHOICE button for 3 seconds to
enter programming mode.
For models 955 & 605 ‘beep’ ‘ON’ --->display shows
‘beep’ ‘OFF’ -->display shows
‘beep ON’ ‘beep OFF’
For other models ‘beep’ ‘ON’ --->FINISHED light is ‘ON’
‘beep’ ‘OFF’ -->FINISHED light is ‘OFF’
‘beep ON’ ‘beep OFF’
2. Press the WATER TEMP button to change the selection, then
press the START/PAUSE button to store the new selection.
NOTE: If you do not press a button within 5 seconds the washing
machine will return to the previous setting. To reprogram, simply
repeat the above process.
When No ‘beep’ at end of cycle is selected, the washing machine
will still ‘beep’ when you press buttons or try to select unavailable
options.
10 Simpson Features of your Washing Machine
The washing machine has WASH, RINSE and SPIN Progress
Indicator lights to let you know where the machine currently is
within the wash program.
You can advance to the next stage of the wash by holding the
START/PAUSE button depressed until the next stage progress
light comes on.
ECO and DEEP are the rinse options available to you on these
models. The difference between Eco and Deep rinse is explained
on page 3 under ‘How does Eco rinse work?’.
We strongly recommend you use Eco rinse whenever you can
to minimise the amount of water used to rinse. However, if your
program selector is at Drip Dry or Woollens deep rinse is selected.
DEEP RINSE uses up to 130% more water than ECO RINSE.
To select DEEP RINSE, press the DEEP RINSE button until the
DEEP RINSE light is ‘ON’. To de-select DEEP RINSE and select
ECO RINSE, press the DEEP RINSE button until the DEEP
RINSE light is ‘OFF’.
If the Deep Rinse light is off, Eco Rinse is the
currently selected option.
NOTE: When you select the WOOLLENS or DRIP DRY program,
DEEP RINSE is automatically selected for you. Eco Rinse is not
available with the Woollens and Drip Dry programs.
IMPORTANT:
•IfyouaregoingtouseFABRICSOFTENER,youMUSTusethe
DEEP RINSE cycle. Fabric softener may cause staining on the
clothes when used with Eco Rinse.
•Ifyourcoldwatersupplypressureisverylow,theEcoRinse
might not be fully effective in rinsing the suds from your clothes.
If this is the case then use the Deep Rinse option.
Turn the WATER LEVEL knob to the Auto-Level position.
Press and hold the WATER TEMP button for 3 seconds to enter
the adjusting mode.
When the machine is in the adjusting mode, the factory set
optimised level is shown by: Warm WATER LEVEL light being
‘ON’, and for models 955 & 605 the digital display shows
.
Press the WATER TEMP button repeatedly to change to the next
Auto adjust setting as shown in the table below.
Models 902,
802 & 552
WATER TEMP
light ON
Display for
models 955 & 605
Auto adjust setting
HOT a water level 20mm higher
than the optimised level
WARM factory set, optimised
water level
COLD a water level 20mm lower
than the optimised level
To Next Page
Loading...
