What does 'MSD-Fac MSD-Vac MSD-Timeout MSD-Zac' error indicate on SMA Inverter?
If the SMA Inverter displays 'MSD-Fac MSD-Vac MSD-Timeout MSD-Zac' often, contact the SMA Serviceline, as it indicates an internal measurement comparison fault or hardware defect.
What does 'K1-Close K1-Open' error mean on SMA WINDY BOY 3300?
If the SMA Inverter displays 'K1-Close K1-Open' often or several times in succession, contact the SMA Serviceline, as it indicates a fault during relay test.
What to do if my SMA WINDY BOY 3300 Inverter shows '!PV-Overvoltage! !DISCONNECT DC!'?
If the SMA Inverter displays '!PV-Overvoltage! !DISCONNECT DC!', immediately disconnect the small wind turbine system from the inverter. First, turn off the line circuit breaker, then stop the small wind turbine system, and disconnect the PV connectors. Check the DC voltage. If it's above the maximum input voltage, review the plant design. If it's below, reconnect the system as described in section 5.5.4. If the message reappears, disconnect the inverter again and contact SMA Serviceline.
What does 'Bfr-Srr' error on SMA Inverter indicate?
If the SMA Inverter displays 'Bfr-Srr' often, contact the SMA Serviceline, as it indicates an internal measurement comparison fault or hardware defect.
What does 'Riso' error mean on my SMA WINDY BOY 3300 Inverter?
If the SMA Inverter displays 'Riso', the electrical insulation between the small wind turbine system and ground is faulty. Check the system insulation and check the system for ground faults as described in section 9.3.1.
Why does my SMA Inverter show 'Fac-Bfr Fac-Srr FacFast' errors?
If your SMA Inverter is showing the 'Fac-Bfr Fac-Srr FacFast' error, the grid frequency is no longer within the permissible range. If the grid frequency is within the tolerance range, yet the errors are being displayed often, contact the SMA Serviceline.
What does 'dZac-Bfr dZac-Srr' mean on my SMA Inverter?
If the SMA Inverter displays 'dZac-Bfr dZac-Srr', it means sudden changes in grid impedance exceed the permissible range. Check the grid impedance and observe how often major deviations occur. If repeated frequency variations occur and this is causing the errors, ask the utility operator if it would agree to modify the operating parameters (dZac-Max). Discuss changing the operating parameter with the SMA Serviceline.
Why is my SMA WINDY BOY 3300 showing 'Trafo-Temp-W' error?
If the SMA Inverter displays 'Trafo-Temp-W', it means the transformer has reached an unacceptably high temperature. Check the heat dissipation.
What causes 'Trafo-Temp-F' error on my SMA WINDY BOY 3300?
If the SMA Inverter displays 'Trafo-Temp-F', the temperatures in the transformer have exceeded the acceptable limit. If this problem recurs, check the heat dissipation of the inverter, as described in section 8.1.
How to fix 'Zac-Bfr' or 'Zac-Srr' error on SMA WINDY BOY 3300?
If your SMA Inverter displays 'Zac-Bfr' or 'Zac-Srr', the grid impedance has left the permissible range. Check the grid impedance and grid connection on the inverter. Use an AC cable with an adequate cross-sectional area (low impedance). If required, check and re-tighten the screws on the AC terminals. If this fault recurs, contact the SMA Serviceline.
General| Model | WINDY BOY 3300 |
|---|---|
| Rated Output Power | 3300 W |
| Max. DC Power | 3400 W |
| AC Nominal Power | 3300 W |
| Max. Apparent AC Power | 3300 VA |
| Max. Input Current | 20 A |
| Number of MPP Trackers | 1 |
| European Efficiency | 95.5% |
| Nominal AC Voltage | 230 V |
| Cooling | Convection |
| Operating Temperature Range | -25°C to +60°C |
| Protection Class | IP65 |
| AC Voltage Range | 180 V to 280 V |
| Nominal AC Frequency | 50 Hz |
To Next Page
