How to open Smeg WHT812EIT-1 Washer door when locked?
If your Smeg washer's loading door won't open, the door lock may be activated due to the water level. Drain the water by running the Pump or Spin program. Alternatively, the machine might be heating water or spinning; wait until the program completes. Also, check if the child lock is engaged and wait a couple of minutes after the program ends for it to deactivate.
Why is my Smeg WHT812EIT-1 not filling with water?
If your Smeg washer isn't filling with water, first, ensure the tap is turned on. Check if the water inlet hose is bent and flatten it if necessary. Also, clean the water inlet filter if it's clogged, and make sure the loading door is fully closed.
Why is my Smeg WHT812EIT-1 Washer vibrating so much?
If your Smeg washer is vibrating or making noise, it might be unbalanced. Adjust the feet to level it. Also, check for hard substances in the pump filter and remove any transportation safety bolts. Ensure the machine isn't leaning on anything and adjust the laundry quantity as needed.
What to do if my Smeg WHT812EIT-1 leaves laundry wet?
Excessive foam due to too much detergent can cause laundry to remain wet. Use the recommended amount of detergent to prevent this.
Why does my Smeg Washer immediately drain water?
If your Smeg washer is discharging water immediately, ensure the draining hose is connected at the correct height as described in the operation manual.
How to improve stain removal in my Smeg Washer?
If your Smeg washer's washing performance is poor with stains persisting or laundry not whitening, ensure you're using the recommended amount of detergent, not overloading the machine, selecting the correct program and temperature, and using the right type of detergent. Also, make sure to put the detergent in the correct compartment and avoid mixing bleaching agents with detergent.
Why does my Smeg Washer take so long to wash?
If your Smeg washer is taking longer than usual, it could be due to low water pressure, low voltage, or low input water temperature. The machine waits until it takes in enough water or reaches the selected temperature. Also, the number of rinses might have increased, or excessive foam might have occurred. Use the recommended amount of detergent.
Why won’t my Smeg WHT812EIT-1 Washer go to the spinning step?
If your Smeg washer is not switching to the spinning step, there might be an unbalanced load. The automatic unbalanced load detection system might be activated due to the laundry's distribution in the drum. Also, the machine will not spin if water is not drained completely, so check the filter and the draining hose. Excessive foam from too much detergent could also be the cause; use the recommended amount.
Why is my Smeg Washer not draining water?
If your Smeg washer is not draining water, the drain hose may be clogged or twisted, or the pump filter may be clogged. Clean or flatten the hose and clean the pump filter to resolve this issue.
General| Type | Freestanding |
|---|---|
| Appliance placement | Freestanding |
| Product colour | White |
| Capacity | 8 kg |
| Energy Efficiency Class | A |
| Spin Speed | 1200 RPM |
| Built-in display | Yes |
| Door hinge | Left |
| Drum material | Stainless steel |
| Drum volume | 52 L |
| Spin-drying class | B |
| Washing class | A |
| Noise level (spin) | 76 dB |
| Delayed start timer | Yes |
| Delay start (max) | 24 h |
| Remaining time indication | Yes |
| Water consumption washing per cycle | 50 L |
| Noise Level (Spinning) | 76 dB |
| Delay Start | Yes |
| Child Lock | Yes |
| Display | Yes |
| Programs | Cotton, Quick, Synthetics |
| Loading type | Front-load |
| Control type | Rotary |
| Water Consumption | 50 L |
To Next Page
