What to do if it is not possible to manually operate the switch of Socomec Industrial Electrical?
If it is not possible to manually operate the switch, verify the following: * That the front selector switch position is on the Manual position. * That the product is not padlocked. * The rotation direction of the handle. * Apply a sufficient progressive action in the direction as indicated on the handle.
What to check if nothing happens following a loss of the priority source on Socomec Industrial Electrical (application Main-Gen)?
If nothing happens following a loss of the priority source (application Main-Gen), you should: * Check the setting of 1FT. After 1FT has counted down 71-72-74 should change state. * Check the status of the "gen set start" contact (contact 71-73-74) after 1FT countdown. * Check the wiring from the "gen set start" contact (71-72-74) to the generating set controller.
What to do if socomec Switch ATyS S does not respond to remote orders?
If the socomec ATyS S switch doesn't respond to remote commands, first, put the product into manual mode and switch to the zero position using the emergency handle. Then, reset by switching from manual to auto in the zero position. Also, check that the AUX Supply voltage is within limits and confirm that the remote signals are being received.
Why socomec ATyS s electrical operation does not correspond to expected behavior?
If the electrical operation of your socomec Switch does not match the expected behavior, verify the selected control logic wiring (impulse or contactor). For Impulse, ensure >60ms with these connections: 314 – 317 (Switch to position II), 315 – 317 (Switch to position I), 316 – 317 (Switch to position 0). For Maintained, check the bridge between 316 – 317 for Contactor Logic (Return to zero).
How to manually operate socomec ATyS s Switch?
To manually operate the socomec switch, ensure the front selector switch is in the Manual position. Also, check that the product is not padlocked and verify the rotation direction of the handle.
How to troubleshoot socomec Switch ATyS S that does not operate electrically?
If the socomec ATyS S switch isn't operating electrically, check the power supply on terminals 101 to 402, ensuring it's within the correct voltage range: 12Vdc (9 – 15Vdc), 24/48Vdc (17 – 62Vdc), or 230Vac (160 – 310Vac). Also, verify that the front selector switch is in the (AUT) position and check the contact terminal and contact signals between 314 and 317, which should be normally open contacts with priority to signals I & II.
Why is it impossible to padlock socomec ATyS s Switch?
If you cannot padlock the socomec Switch, first verify that the front selector switch is in the padlocking position. Secondly, ensure that the emergency handle for manual operation is not inserted into the ATyS S manual slot. Finally, confirm that the ATyS S is in the 0 position, as padlocking is only possible in this position with the emergency manual operation handle removed.
Why does the fault LED turn on in Socomec Industrial Electrical (ATS Controller)?
The fault LED on the ATS Controller might be on because an external fault/alarm condition is active through one of the ATyS configurable inputs. This is normal and can be reset by opening the associated contact input. To attempt to solve the problem, switch the ATyS p from AUT to Manual and back to AUT.
Why is the SOURCE availability indicator not illuminating on my Socomec Industrial Electrical device?
If the SOURCE availability indicator does not illuminate when the source is available, try the following: * Press the "LED test" button and ensure that the corresponding LED’s illuminate. * Check in programming mode that the nominal voltage value (by default set to 400V), the nominal frequency value and the network configuration correspond to the network and modify if necessary. * Check the voltage and frequency thresholds and hysteresis for this source, in the Volt and Frequency menus and modify if necessary.
What to do if electrical operation does not correspond to external order I,O,II on Socomec Industrial Electrical?
If the electrical operation does not correspond to external order I,O,II, you should: * Verify the selected control logic wiring (impulse or contactor). * Verify the connector connections.
General| Product Category | Transfer Switch |
|---|---|
| Protection Degree | IP20 |
| Operating Mode | Manual |
| Electrical Durability | 1, 000 cycles |
| Control Voltage | 24 V DC |
To Next Page
