To Next PageTo Next PageWhy does my SOLIS S5-EH1P3.6K-L Inverter say NO-Battery?
If your SOLIS Inverter displays 'NO-Battery', it means the battery is not connected. Check the information page to verify the battery voltage is within the correct range. Measure the battery voltage at the plug.
How to fix IGBT-OV-I (1048 DATA:0000) error on SOLIS S5-EH1P3.6K-L?
If your SOLIS Inverter shows 'IGBT-OV-I (1048 DATA:0000)', which means there is an IGBT overcurrent, try restarting the system and see if the error clears.
What does GRID-INTF02 (1046 DATA:0000) error mean on SOLIS S5-EH1P3.6K-L?
If your SOLIS Inverter displays 'GRID-INTF02 (1046 DATA:0000)', it indicates a power grid disturbance. First, check if the grid is heavily distorted. Then, check that the AC cable is securely connected.
What does OV-Vbatt mean on my SOLIS S5-EH1P3.6K-L?
If your SOLIS Inverter displays 'OV-Vbatt', it means that battery undervoltage was detected. Verify the battery voltage is within the specified range. Measure the battery voltage at the inverter connection point. Contact your battery manufacturer for further assistance.
Why does my SOLIS S5-EH1P3.6K-L show IGFOL-F error?
If your SOLIS Inverter shows the error 'IGFOL-F', it means the grid current tracking has failed. To troubleshoot this: 1. Check to see if there are any known issues with the power grid in your area. 2. Make sure the AC cable is securely and correctly connected. 3. Restart the inverter to see if the problem goes away.
What to do if SOLIS S5-EH1P3.6K-L shows OV-G-V03 error?
If your SOLIS Inverter displays 'OV-G-V03', it indicates a grid transient overvoltage. Try restarting the system to see if the error disappears.
What causes DCInj-FAULT (1037 DATA:0000) error on SOLIS S5-EH1P3.6K-L?
If your SOLIS Inverter shows the error 'DCInj-FAULT (1037 DATA:0000)', it means that the DC component of the current is too high. To solve this: 1. Make sure there are no known problems with the power grid. 2. Check the AC cable to be sure it is properly connected. 3. Restart the inverter to see if the problem goes away.
How to fix OV-TEM (1032 DATA:0000) error on SOLIS S5-EH1P3.6K-L Inverter?
If your SOLIS Inverter displays 'OV-TEM (1032 DATA:0000)', it means the module is overheating. Check if the inverter has enough space around it for proper ventilation. Also, check that the installation is correct according to the manual.
Why does my SOLIS S5-EH1P3.6K-L show OV-G-V01 error?
If your SOLIS Inverter shows the error 'OV-G-V01', it means the grid voltage is exceeding the upper voltage range. To address this: 1. Check to see if there are any known issues with the power grid in your area. 2. Make sure the AC cable is securely and correctly connected. 3. Restart the inverter to see if the problem goes away.
What to do if SOLIS S5-EH1P3.6K-L shows a Surge Alarm?
If your SOLIS Inverter displays a 'Surge Alarm', it indicates a surge on the grid side. First, try restarting the device. If the alarm persists after restarting, it means the issue hasn't been resolved and you should contact the manufacturer's customer service for further assistance.
General| Model | S5-EH1P3.6K-L |
|---|---|
| Type | Hybrid Inverter |
| Rated Power | 3.6kW |
| Max. DC Input Power | 5.4kW |
| Rated AC Output Power | 3.6kW |
| Rated Grid Voltage | 230V |
| Grid Voltage Range | 180-280V |
| Rated Grid Frequency | 50/60Hz |
| Total Harmonic Distortion (THD) | <3% |
| DC Switch | Yes |
| Ingress Protection | IP65 |
| Cooling | Natural Convection |
| Weight | 17.7 kg |
| Dimensions | 310 x 563 x 219 mm |
| Operating Temperature Range | -25°C to +60°C |
| Communication | RS485 |
| Protection | over temperature, over voltage |
