Sontheim Verona COMhawk xt - GPS Position Retrieval; GPS Position

To Next Page

To Previous Page

Operations Manual

Sontheim_Telemetry_Verona_Gen 4_operations manual.docx Version of the Document: 2.1

Figure 16 COMhawk xt Root Directory (Example)

14. GPS Position

To call the GPS position, use the Linux standard program: GPSD.

GPSD-client package is installed. As an example you can use “cgps” for showing the GPS position

within putty.

The output are the GPS coordinates: LON, LAT, height in a Table.

To close cgps enter: [STRG + c] (German keyboard)

To close cgps enter: [CRTL + c] (English keyboard]

Main Page

Table of Contents2
Content2
List of Figures3
List of Tables3
Topic4
Document Reference4
Author4
Date4
History of the Document4
List of Tables Table 1 Document Reference4
Table 2 History of the Document4
Preliminary Note5
Symbols Used5
Safety Instructions5
General5
Target Group5
Electrical Connection5
Tampering with the Device5
General Implementation Instructions6
Requirements on the Installation Point and Position6
Notes on Transport and Storage6
Notes on Wiring and Circuitry7
Intended Use7
Improper Use7
Further Information8
Radio Frequency Safety Cautions8
Label Information9
ECU Interfaces and Vehicle Integration Aspects9
Further Safety Cautions - Country Specific9
Brazil9
List of Figures Figure 1 Label Information9
Operation, Service, Maintenance and Repair, Decommissioning10
Operation10
Maintenance and Repair10
Cleaning and Care10
Inspection and Maintenance10
Repair10
Removal and Replacement10
Disposal10
Extension and Conversion11
Verona Gen 4 Overview11
Verona Gen 4 HW Block Diagram11
Figure 2 Verona Gen 4- Block Diagram11
Comhawk Xt / Verona Gen 4 - Technical Data12
RF Specification13
GSM/UMTS/LTE RF Specifications13
Table 3: System and Functional Requirements (Populated Option Is Bold)13
Antenna Specifications14
Table 4 Bands, Frequencies, Maximum Power and Maximum Antenna Gain for EC14
Table 5 Bands, Frequencies, Maximum Power and Maximum Antenna Gain for FCC / ISED14
Software15
SW Overview15
Figure 3 Function Overview15
Figure 4 Function Overview with more Detailed Clouded Services Explanation15
SW Access to Comhawk Xt16
Operating the Software Via LAN (Verona Gen 4 Is Powered and Connected to the PC Via LAN Cable)16
Figure 5 Network Configuration (in Windows 10)16
Figure 6 Ethernet Configuration16
Operating the Software Via WIFI17
Wifi)17
Figure 7 Setup PUTTY Console17
Figure 8 Verona Gen 4 Response in Putty Console17
Figure 9 Windows 10 WLAN - Networks Available18
Figure 10 WIFI Verona Gen 4 - Automatic Connection18
Figure 11 Putty Console to Connect the Comhawk Xt19
Figure 12 Enter the Login19
Figure 13 Comhawk Xt Is Connected19
Winscp Access20
Figure 14 Start Screen for Winscp20
Figure 15 Comhawk Xt Start Directory Structure (Example)20
GPS Position21
Figure 16 Comhawk Xt Root Directory (Example)21
Insert the SIM Card22
Figure 17 Prepare the SIM Card with the Right Orientation22
Figure 18 Pre-Set the SIM Card with the Right Orientation to Set into the Holder23
Figure 19 Please the SIM Card into the SIM Connector on the PCB. Push Carefully in23
Figure 20 SIM Card Is Connected and Automatically Locked in Operation-Position24
Verona Gen 4 Housing25
Scale Drawings25
Figure 21 3D View Verona Gen 4 Telemetry25
Figure 22 Verona Gen 4 Telemetry - Front View with Dimensions25
Figure 23 Verona Gen 4 Telemetry - Side View with Dimensions26
Figure 24 Verona Gen 4 Telemetry - Detail View: FAKRA Antenna Connection26
Mounting Plate27
Figure 25 Verona Gen 4Telemetry - Definition of Sides27
Figure 26 Mounting Scheme27
Verona Gen 4 Pinout28
Figure 27 Verona Gen 4 Pinout28
Figure 28 30 Pin Receptacle (Rear View)28
Figure 29 Ethernet RJ45-Plug and Network-Cable28

Sontheim Verona COMhawk xt - GPS Position Retrieval; GPS Position

Table of Contents