Sony CDP-3100 - Switch Setting on the Boards

1-10. SWITCH SETTING ON THE BOARDS
1. CDP-3100
AU-183 board
Switches
$101 (S101-1 to $101-8); DIP Switches
Refer to the operation manual for
details.
Factory setting:
$101-1 to S101-4; OFF
$101-5, 6; ON
$101-7, 8; OFF
$2 (S2-1 to S2-8); DIP Switches
For checking design specifications
Set to setting at shipment. Slit lands; At factory setting, the jumper will be soldered to all
Factory setting: the following slit lands.
$2-1 to S2-8; All OFF $L103, SL115, SL124, SL125, SL126, SL127,
$L131, SL134, SL136
Applicable ROM version NO.: V2.00 and higher
Conformation of ROM version No.
Confirm the ROM version No. that appears on the CDP-3100 display(disc data display)when power is turned
ON.
$2(S2-1 to S2-8); DIP switches
S2-1, -2; Remote-3 Command in/Status out change switch
ser
Ts
commen
i
remotes
oTaTUS
OUT]
Par
ters
pns
[pe
|
pws]
Pi)
|
oF
|
ofr
|
pravstop
|
stop
_|
ONAIR
|
ENDALARM
}@)
|
on
|
ore
|
ptavsTor
|
STOP
|
ONAIR_|_STANDBY(INEOUT"OW)
|
|)
|
ofr
[on
|
pLavstop
|
sTop_|
STANBY
|
ENDALARM
|
@
|
on
[
on
|
stanpsy
|
STANDBY
|
INVLID
|
STANDBY(LINEOUT
“ON”
_
NOTE:
In
case
of
(4)
in
the
table
above
and
setting
the
DIP
switch
S2
OFF
on
the
connector
panel
of
the
CDP-3100,
the
machine
is
put
in
STANDBY
mode
when
STOP
command
is
fed
into
Pin-1,
at
that
time,
Pin-2
becomes
invalid.
And
during
the
ONLINE
PLAYBACK
in
the
operating
mode
1
or
2,
STANDBY
command
issued
by
REMOTE-3
can
be
accepted
while
STANBY
key
either
on
CDP-3100
or
on
CDS-3100
is
not
accepted
in
case
of
(3)
or
(4)
in
table above.
Also,
in
case
of
(4)
in
the
table
above,
ONAIR
commandis
not
accepted.
Please
set
the
FADER
key
ON
when
the machine
is controlled
by
REMOTE-3
$2-3; FADER ON switch
By
setting
DIP
switch
Bit-3
ON,
the
faders
are
always
kept
enabled.
(The
fader
button
on
a
remote
does
not
work at this moment.)
e Setting Pause mode
lf
STANDBY
command
is
fed
from
REMOTE-3
during
ON
LINE
PLAYBACK
while
DIP
switch’s
Bit-1,2
and
4
are
ON,
the
machine
temporarily
stops
ONLINE
PLAYBACK.
ft
can
be
restarted
by
PLAY
command
or
pressing PLAY key either on CDP-3100 or CDS-3100.
$2-5 to -8; For checking design specifications
Set to setting at shipment.
Factory setting:
$2-1 to S2-8; All OFF
Warning:
To
change
the
switch
setting,
consult
Sony's
service
person.
CDP-3100 1-7 (E)