2
STR-K885
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be
damaged by heat.
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscou-s (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
About area codes
The area code of the receiver you purchased is
shown on the lower right portion of the rear panel
(see the illustration below).
Any differences in operation, according to the area
code, are clearly indicated in the text, for example,
“Models of area code AA only”.
SURROUND
L
R
CENTER
SURROUND BACK
Area code
Video section
Inputs/Outputs
Video: 1 Vp-p, 75 ohms
COMPONENT VIDEO:
Y: 1 Vp-p, 75 ohms
P
B/CB: 0.7 Vp-p, 75 ohms
P
R/CR: 0.7 Vp-p, 75 ohms
80 MHz HD Pass Through
General
Power requirements
(Models of area code SP, SP6, AUS only)
Power output (DIGITAL MEDIA PORT)
DC OUT: 5V, 700 mA
Power consumption
Power consumption (during standby mode)
0.3 W
Dimensions (width/height/depth) (Approx.)
430 × 157.5 × 310 mm
including projecting parts
and controls
Mass (Approx.) 7.6 kg
Area code Power requirements
SP, SP6 230 – 240 V AC, 50/60 Hz
AUS 240 V AC, 50 Hz
AR 220 – 230 V AC, 50/60 Hz
E51 120/220/240 V AC,
50/60 Hz
Area code Power consumption
SP, SP6, AUS, E51, AR 200 W
4)
You can change the AM tuning scale to 9 kHz or
10 kHz. After tuning in any AM station, turn off
the receiver. While holding down TUNING
MODE, press ?/1. All preset stations will be
erased when you change the tuning scale. To reset
the scale to 10 kHz (or 9 kHz), repeat the
procedure.
Design and specifications are subject to
change without notice.
•Abbreviation
AR : Argentine model
AUS: Australian model
E51 : Chilean and Peruvian models
SP : Singapore model
SP6 : Singapore and Malaysia models
Parts No.
MODEL IDENTIFICATION
– Rear Panel –
Model Part No.
SP, SP6 models 2-897-029-1[]
AUS model 2-897-029-2[]
E51 model 2-897-029-3[]
AR model 2-897-029-4[]
Ver. 1.1
To Next Page
Loading...
