Sony Trinitron PVM-1271Q - Specifications

SPECIFICATIONS
Color system PAL, SECAM, NTSC and NTSC, 43 systems, Inputs Mies IN: BNC connector
switched
automatically
VTR:
8-pin
connector,
Pin
No.
2
(pin
No.
Picture
tube
Trinitron
tube
6:
ground)
Approx.
33
cm
(13
inches),
90-degree
deflec-
composite
1
Vp-p
+6
dB,
sync
negative,
tion, Super Fine Pitch 0.25 mm 75 ohms and high impedance switchable
(Approx. 31 cm picture measured diagonally) cee IN: mini jack
Resolution
RGB
inputs:
600
lines,
640
x
200
dots
VTR:
8-pin
connector,
Pin
No.
1
(pin
No.
Composite input: 550 lines 5: ground)
Color
temperature
PVM-1271Q:
9,300°K
—5
dBs,
high
impedance
PVM-1371QM: 6,500°K EXT SYNC IN: BNC connector
(Can
be
changed
to
either
temperature
by
composite
sync
2
-
8
Vp-p,
negative,
an internal switch. For switching of the col- 75 ohms and high impedance switchable
or temperature, consult your authorized RGB IN: BNC connector
Sony dealer.) 0.7 Vp-p, +6 dB, 75 ohms, non composite
Frequency response 10 MHz (~3 dB, RGB) AUDIO (RGB) IN: mini jack
5.5 MHz (-3 dB, composite video) —5 dBs, high impedance
Horizontal
linearity
+8%
CMPTR:
25-pin
connector
Vertical linearity +5% For details, see “CMPTR connector”.
Line pull range Horizontal +500 Hz Outputs VIDEO OUT: BNC connector
Vertical 8 Hz AUDIO OUT: mini jack
Overscan of the picture Output level 1W
5% EXT SYNC OUT: BNC connector
Underscan of the picture RGB OUT: BNC connector
9% AUDIO (RGB) OUT: mini jack
Return loss 4 MHz, 35 dB (LINE A, LINE B) Loop-through
Zooming Within 2% Power requirements PVM-1271Q: 120 V ac, 50/60 Hz
Convergence Central area 0.6 mm PVM-1371QM: 220 - 240 V ac, 50/60 Hz
Periphery 0.8 mm Power consumption PVM-1271Q: 105 W max.
Brightness More than 35 foot-lamberts PVM-1371QM: 90W
Dimensions Approx. 346 x 339 x 388 mm (w/h/d)
(135/e x 133/28 x 153/a inches)
Weight Approx. 14.5 kg (31 Ib 15 oz)
CMPTR connector (25-pin)
Pin assignment
9 10 11 12 13
o909000 00000000
oo 000 0000000
14418 16 17 18 19 20 21 22 23 24 25
Pin No. | Signal Signal level
1" IBM select High state (6 V): IBM mode
Low state: 3 Bit TTL
enon need
2 Audio select High state (5 V or open): Audio inputs from pin 13.
Low state (less than 0.4 V): Audio inputs from the LINE A AUDIO IN jack
H. sync or composite sync
Negative polarity
When the high state is selected at pin 9:
1V p-p, 75-ohm terminated
When the low state is selected at pin 9:
TTL level
4 Blue input Positive polarity
When the high state is selected at pin 9:
; Analog signal (0.7 V p-p, 75-ohm terminated, non sync)
5 Green input When the low state is selected at pin 9:
6 Red input Digital signal (TTL level)
7 +12 V power supply 0.3 A max
8 +5 V power supply 0.6 A max
9* Analog/digital mode select High state (open): Analog signal (0.7 V p-p)
Low state (ground): Digital signal (TTL level)
14