Why is the picture from my INPUT A connector colored strange on my Sony VPL-VW50 Projector?
If the picture from the INPUT A connector on your Sony Projector appears colored strange, select “Computer,” “Component,” or “Video GBR” for “Input-A Signal Sel.” in the Setup menu according to the input signal.
What does it mean when the ON/STANDBY light on my Sony Projector flashes red 4 times?
If the ON/STANDBY light on your Sony Projector flashes red four times, consult with qualified Sony personnel.
Why is the picture from my VIDEO INPUT or S VIDEO INPUT connector colored strange on my Sony Projector?
If the picture from the VIDEO INPUT or S VIDEO INPUT connector on your Sony Projector appears colored strange, try adjusting the picture settings in the Picture menu. You can also set the “Color System” in the Setup menu to match the color system being input.
What does it mean when the LAMP/COVER light on my Sony VPL-VW50 flashes red 2 times?
If the LAMP/COVER light on your Sony Projector flashes red twice, make sure the lamp cover is securely closed and the screws are tightened. Also, ensure the filter holder is securely closed.
What does it mean when the ON/STANDBY light on my Sony VPL-VW50 Projector flashes red 2 times?
If the ON/STANDBY light on your Sony Projector flashes red twice, check that nothing is blocking the ventilation holes. Also, verify whether the projector is being used at a high altitude.
What does it mean when the LAMP/COVER light on my Sony Projector flashes red 3 times?
If the LAMP/COVER light on your Sony Projector flashes red three times, try replacing the lamp. You can also wait for the lamp to cool down before turning the power back on.
What does it mean when the ON/STANDBY light on my Sony VPL-VW50 flashes red 6 times?
If the ON/STANDBY light on your Sony Projector flashes red six times, disconnect the AC power cord and make sure the ON/STANDBY lamp turns off. After that, reconnect the power cord and try turning the power on again. If the issue persists, consult with qualified Sony personnel.
Reduces risk of fire or electric shock; avoid electrical shock; refer servicing to qualified personnel.
Device complies with FCC Rules Part 15 for Class B digital devices, ensuring protection against harmful interference.
Contains mercury; consult local authorities for safe disposal following fluorescent lamp guidelines.
Compliance with Canadian ICES-003 and EU WEEE directive for electrical equipment disposal.
Check voltage, avoid liquids, unplug when not in use, disconnect by plug, secure outlet access.
Do not disconnect from outlet while cooling fan runs; ensure ventilation holes are clear.
Identifies buttons, indicators, and connectors on the front and right panel of the projector.
Details features and openings on the rear and bottom of the projector unit.
Diagram and explanation of buttons on the remote control for projector operation.
Lists package contents and provides instructions for inserting batteries into the remote control.
Avoid locations with dust, smoke, high humidity, extreme temperatures, or poor ventilation.
Avoid blocking ventilation, limit tilting angles, and adjust cooling for high altitudes.
Determines projector and screen placement for optimal picture quality using lens shift.
Provides detailed projection distance measurements for 16:9 and 4:3 aspect ratio screens.
Align projector lens parallel to screen; project image and adjust to fit screen.
Guide for connecting DVD players, recorders, tuners, etc. via component video cables.
Instructions for connecting devices with HDMI output for enhanced picture quality.
Connect VCRs or other equipment without component connectors using S-Video or video cables.
Connect a computer using HD-Dsub15 or HDMI cables for display output.
Guide to adjusting picture position using remote control or projector buttons.
Turn on projector, select input, and adjust vertical picture position using lens shift.
Use the Lens Zoom function to adjust the picture size by pressing the arrow buttons.
Adjust picture focus and use adjusters to level the projector on uneven surfaces.
Choose from 16 languages for on-screen menus and displays; English is the default.
Steps to navigate the menu to select a new language for the user interface.
Displays the available languages for selection in the setup menu.
Power on equipment, select input source via INPUT button to display desired picture.
Follow steps to turn off the projector; fan continues running to cool internal heat.
Select from various wide screen modes like Full, Normal, and Wide Zoom for different aspect ratios.
Explains Zoom, Full 1, and Full 2 modes; notes on aspect ratio changes and copyright.
Choose between Dynamic, Standard, Cinema, or custom User modes for optimal viewing.
Use ADJ PIC to adjust contrast, brightness, color, hue, and sharpness.
Detailed steps for adjusting picture quality items like contrast and brightness.
Adjust color and hue of specific targets independently for personalized picture appearance.
Fine-tune specific color portions and hue using RCP controls for desired visual output.
Navigate on-screen menus for adjustments; language selection is covered separately.
Steps to press MENU, select menu item, and view/adjust settings.
Explains pop-up, setting, adjustment, and next menu windows for various settings.
Adjust settings, change selections, clear menus, or reset items to factory defaults.
Select viewing modes (Dynamic, Standard, Cinema, User) and store custom settings.
Details on adjusting Advanced Iris, Lamp Control, Contrast, Brightness, Color, Hue, Temp., Sharpness.
Explanation of Noise Reduction (NR), DDE, Black Level Adj, and Gamma Correction settings.
Adjust color/hue using RCP and convert color reproduction range with Color Space.
Set aspect ratio (Wide Mode) and control overscan for image display.
Adjust screen area, V Center, V Size, and fine-tune input signal parameters (APA, Phase, Pitch, Shift).
Configure Status, Language, Cooling, Standby, and Power Saving settings.
Select Input-A signal type, color system, and configure lamp settings.
Configure Auto Input Search, Test Pattern display, and background color.
Correct V Keystone, flip image, control lens operation, and select IR receiver settings.
Adjust the displayable region within screen edges; set V Keystone to '0' when using Blanking.
View model name, serial, frequencies, lamp timer, signal type, and preset memory details.
Solutions for power-on failures and common picture problems like no picture or strange colors.
Addresses picture flickering, display issues, remote control problems, and fan noise.
Explains the causes and remedies for flashing red indicators on ON/STANDBY and LAMP/COVER.
Lists common warning and caution messages with their respective causes and remedies.
Detailed steps for replacing the projector lamp, including safety precautions and tools.
Continues lamp replacement process and removal of the air filter holder and filter.
Attach air filter, clean ventilation holes, reassemble, and confirm lamp replacement.
Instructions on when and how to clean the air filter using mild detergent.
Details on projection system, LCD panel, lens, lamp, and video/computer input signals.
Lists items included with the projector and available optional accessories.
Table of preset video signals, their formats, frequencies, and sync types.
Lists preset computer and video signals, including resolution and sync information.
Maps analog and digital signals to their corresponding preset memory numbers for optimal display.
Indicates which menu items are adjustable for different input signal types (Video, Component, GBR, Computer).
Details screen menu options like Wide Mode, Over Scan, V Position, and Shift for various inputs.
Guidelines for installing the projector on a ceiling using suspension supports.
Provides installation measurements for PSS-H10 and PSS-610 suspension supports for 16:9 and 4:3 screens.
Top view illustration showing dimensions for attaching the PSS-H10 suspension support.
Front and side view diagrams illustrating dimensions for PSS-H10 projector ceiling mounting.
Installation measurements for PSS-610 support with 16:9 and 4:3 screens.
Formulas to calculate installation measurements for PSS-610 suspension support based on screen size.
Front and side view diagrams detailing dimensions for PSS-610 projector ceiling mounting.
Tools and steps for making fine adjustments to the horizontal picture position.
Procedure for moving the lens left/right and adjustment levels for 16:9 screens.
Tighten screws to fix the lens in place and attach the washer ring.
Power| power consumption in operation | 300 W |
|---|---|
| power consumption in standby | 8 W |
| power requirements | AC 100 to 240 V, 1.3 to 3 A, 50/60 Hz |
Operating Environment| operating temperature | 5°C to 35°C |
|---|---|
| operating humidity | 35% to 85% (no condensation) |
Display| native resolution | 1080p |
|---|---|
| display resolution | 1920 x 1080 |
| contrast ratio | Up to 15000:1 |
Inputs and Outputs| component video input | 1 (Side) |
|---|---|
| composite video input | 1 (Side) Vp-p+/-2 dB sync negative (75 ohms terminated) |
| s-video input | Y/C mini DIN 4-pin type |
Weight and Dimensions| weight | 11 kg |
|---|---|
| measurements | 395 x 173.5 x 471.4 mm |
To Next Page
