SPECIFICATIONS
Audio Sections
Power
Output
20W
Continuous x 4 Channels into
40
for
80
Watts Total Amplification;
35Hz
to
20kHz
THD
(at
rated
power)
<1.00%
Damping
Factor
>15
Input Sensitivity
(For
rated
power@
max
VC.
analog
L&R
Inputs)
335mV
Input
Impedance
(analog
L&R
Inputs)
Input
Overload
(analog
L&R
Inputs)
Frequency Response
Channel Separation
Cross
Talk
Between Sources
S/N
Ratio (A-Wtd,
db
below
1 Watt)
Bass
Control Range
Treble Control Range
Speakers
Down-firing Subwoofers
Mid Range Drivers
Tweeters
Power Consumption 120V Version
Standby
No signal (idle)
At
1/8
of
Rated Power
(2.5
Watts/Channel. 40)
Rear Panel marked Line Ratings
Dimensions
(H
X W X
D)
4" X 28" X 16-1/2" (102mm X 711mm X 419mm)
16" (406mm) Depth with grille
removed
Weight
251bs
(11
kg)
20
K Ohms
2.0Vrms
35
Hz
to
20
kHz
>
50
dB
@
10
kHz
>
60
dB
@ 1 0
kHz
-78
dB
+ 8 dB@ 100Hz
+ 6 dB/-10dB @ 10kHz
Two x
5-1
/4"
Treated Paper
Cone
Four x
2-1
/2"
Treated Paper
Cone
Two x
1"
Silk
Dome
<0.5 Watts
14
Watts
40
Watts
1
00-240V-
50-60Hz 1
OOW
0
Bluetooth
®
m
The
Bluetooth®
word
mark
and
logos are registered trademarks
owned
by Bl
ue
tooth
SIG
. Inc.
and
any
use
of
such marks
by
SpeakerCraft.
LLC
is
under
license. Other trademarks
and
trade
names are those
of
their respective owners.
~
FCC Warning
0 3
X-CS3
•
This
device
complies with Part
15
of the
FCC
Rules.
Operation
is
subject
to
the following
two
conditions:
• (
1)
Thi
s
de
vice
ma
y
not
cause harmful interference,
and
•
(2)
This
device
must
accept
an
y interference receiv
ed
. including inter-
ference
that
may
cause undesired operation.
• Changes or modifications
not
expressly
appro
v
ed
by the party
responsible for
compliance
could void the
user's
authority to
operate
the equipment.
•
NOTE
:
This
equipment
has
been
tested
and
found to
comply
with the limits
for a
Class
B digital device. pursuant
to
Part
15
of
the
FCC
Rules
.
These
limits
are
de
s
igned
to
provide reasonable protection against harmful interference
in
a residential installation.
This
equipment
generates.
uses
and
can
radiate
radio frequency energy
and
.
if
not installed
and
used
in
accordance
with
the instructions.
may
cause harmful interference
to
radio communications.
14
Howeve
r.
there
is
no
guarantee
that interference will
not
occur
in
a particular
installation.
If
this
equipment
does cause harmful interference
to
radio or tele-
vision
reception. which
can
be
determined by turning the
equipment
off
and
on. the user
is
encouraged
to
try
to
correct the interference
by
one
or more
of
the followi
ng
measures:
•
--
Reorient or relocate the receiving antenna.
• -- Increase the separation
between
the
equipment
and
rece
iver.
•
--
Connect
the
equipment
into
an
outlet
on
a circuit different from that
to which the receiver
is
connected
.
• --Consult the
dealer
or on experienced radio/TV technician for help.
To Next Page
Loading...
Need help?
General
