ST X-NUCLEO-LPM01A - Figure 14. STM32 Nucleo32 Target Board Plugged into the X-NUCLEO-LPM01 A

41 pages

To Next Page

To Previous Page

UM2243 Rev 2 21/41

UM2243 Power supply connections of a target board

Figure 14. STM32 Nucleo32 target board plugged into the X-NUCLEO-LPM01A

Main Page

Default Chapter1
- Figure 1. X-NUCLEO-LPM01A1
- Table of Contents2
1 Features7
2 Product Marking8
3 System Requirements8
4 Software Tool and Embedded Software9
- Embedded Software9
- PC Software Tool9
5 Ordering Information9
- Table 1. Ordering Information9
6 Hardware Layout and Configuration10
- Figure 2. Hardware Block Diagram10
- Figure 3. X-NUCLEO-LPM01A Layout Top View11
- X-NUCLEO-LPM01A Layout11
- Figure 4. X-NUCLEO-LPM01A Layout Bottom View12
7 Supplying Power to the X-NUCLEO-LPM01A13
- Power Source from an USB Host Port (Default Setting)13
- Table 2. Power Input Source Setting Summary13
- Power Source from a USB Charger14
- Figure 5. JP3 (USB Setting)14
- Figure 6. JP3 and JP2 (USB Charger Setting)14
- Power Source from an External DC Power Supply15
- Figure 7. JP3 and CN7 (Ext Pwr Setting)15
- Power Source from the 5 V Pin of the Arduino uno or Arduino Nano Connectors16
- X-NUCLEO-LPM01A Power Consumption16
- Figure 8. JP3 (Power from Arduino Setting)16
- Figure 9. CN4 and CN13 +5V Pin Assignment16
8 Power Supply Connections of a Target Board17
- Table 3. Power Output Related Jumper and Connector Settings17
- Figure 10. Pins AREF and 3V3 of Arduino uno Connectors CN4 and CN318
- Jumpers JP1, JP9, JP10, JP418
- Figure 12. Jumper Setting for Arduino with Nucleo Target Board19
- Settings for Use of the Arduino uno Connectors with Nucleo64 and Nucleo144 Use Cases19
- Figure 13. STM32 Nucleo64 Target Board Plugged into the X-NUCLEO-LPM01A20
- Settings for Use of the Arduino Nano Connectors in a Nucleo32 Use Case20
- Figure 14. STM32 Nucleo32 Target Board Plugged into the X-NUCLEO-LPM01A21
- Power Supply Connections of a Target Board with Basic22
9 Static Current Measurement Principle23
- Figure 16. Static Current Measurement Principle23
10 Dynamic Current Measurement Principle24
- Figure 17. Dynamic Current Block Diagram24
- Dynamic Current Block Diagram Description25
- Behavior for Dynamic Current Measurements25
- Dynamic Current Measurements Special Care26
Standalone Mode Using Embedded User Interface27
- Figure 18. Embedded User Interfaces Elements27
Host-Controlled Mode with a PC28
Trigger Signals between the X-NUCLEO-LPM01A29
And the Target Board29
- Trigger Signal from the Target Board to the X-NUCLEO-LPM01A29
- Figure 19. Arduino D7 Trigger Signal from Target Schematics29
- Figure 20. Arduino uno D7 Trigger Signal from Target and Solder Bridges SB2630
- Figure 21. Arduino Nano D7 Trigger Signal from Target30
- Trigger Signal from X-NUCLEO-LPM01A to Target Board31
- Figure 22. Arduino D2, D3 Trigger Signal to Target Schematics31
- Figure 23. Arduino uno D2, D3 Trigger Signal to Target and Solder Bridges SB3, SB531
- Figure 24. Arduino Nano D2, D3 Trigger Signal to Target32
Extension Connector CN1133
- Extension Connector Used with Arduino uno Connectors33
- Figure 25. Extension Connector CN11 with Arduino uno33
- Extension Connector Used with Arduino Nano Connectors34
- Switch to Select the Type of Daughterboard34
- Figure 26. Extension Connector CN11 with Arduino Nano34
How to Adapt an STM32L432 Nucleo-32/Nucleo-6435
Nucleo-144 to Power the MCU from the Arduino35
AREF Pin35
- How to Adapt an STM32L432 Nucleo-32 to Power the MCU from the Arduino AREF Pin35
- How to Adapt an STM32L476 Nucleo-64 to Power the MCU from the Arduino AREF Pin35
- How to Adapt an STM32L496 Nucleo-144 to Power the MCU from the Arduino AREF Pin36
Statement of Compliance to Local Legislation37
- FCC Compliance Statement37
- IC Compliance Statement37
  - Compliance Statement37
  - Déclaration de Conformité38
- CE Compliance Statement38
- Table 5. Reference Documents39
- Table 6. Document Revision History40

ST X-NUCLEO-LPM01A - Figure 14. STM32 Nucleo32 Target Board Plugged into the X-NUCLEO-LPM01 A

Table of Contents

Related product manuals