Stanley ProSert XTN20

Other manuals for Stanley ProSert XTN20

Service Manual24 pages

Accessories Manual8 pages

Questions and Answers

B
Brian ThompsonAug 21, 2025
Why Stanley Rivet Tools does not spin on?
- D
  david42Aug 22, 2025
  Your Stanley Rivet Tool might not be spinning on due to several reasons. First, check if the Chuck Nut 14 is loose and tighten it. Also, ensure there is an air supply connected. If these aren't the issue, there might be an insufficient gap between Locking Nut 17 and Piston 18A, so adjust the gap to 1.5mm/2mm. Another potential cause is a Motor Rod 17M that is too short, requiring replacement. Finally, the Air Motor could be jammed; try lubricating the tool at the air inlet, and if that doesn't work, dismantle and clean it thoroughly.
P
Patricia LynchSep 4, 2025
What to do if stroke adjustment very hard by hand in Stanley Rivet Tools?
- A
  Andrew GreenSep 4, 2025
  If the stroke adjustment is very hard to do by hand on your Stanley Rivet Tools, it is caused by excessive pressure. Use a pin punch (07900-00624) to aid stroke adjustment.
L
Lydia BrockSep 2, 2025
Why Stanley Rivet Tools drive screw returns very slow to forward position?
- K
  Katherine DavisSep 2, 2025
  If the drive screw returns very slowly to the forward position on your Stanley Rivet Tools, it's likely because the trigger is being released early. To speed up the operation, ensure the trigger is held throughout the full cycle.
J
jeremygilmoreSep 1, 2025
How to fix insert will not place onto mandrel in Stanley Rivet Tools?
- S
  Steven MarshSep 1, 2025
  If the insert won't place onto the mandrel of your Stanley Rivet Tools, it might be due to an incorrect Blind Rivet Nut thread size, so change to the correct size. An incorrectly fitted Mandrel A could also be the problem, so change to the correct size Mandrel. A worn or damaged Mandrel A should be replaced. Finally, ensure the nose equipment is correctly assembled by refitting it.
K
Kevin SosaAug 30, 2025
What to do if Stanley Rivet Tools mandrel turns independent of motor?
- A
  Amanda RobinsonAug 31, 2025
  If the mandrel turns independently of the motor in your Stanley Rivet Tools, it could be due to a worn or damaged Drive Shaft E or a worn or damaged Mandrel A; in both cases, replace the part. Also, check if the Chuck Nut 14 is loose and tighten it.
S
Susan SmithAug 29, 2025
What to do if Stanley Rivet Tools trigger inoperative?
- A
  Amy GrahamAug 29, 2025
  If the Trigger 12 on your Stanley Rivet Tool is inoperative, it could be due to static friction. Try depressing and holding the Trigger 12 a few times. Low air pressure could also be the cause, so increase the air pressure. If the Valve Slider 9 remains stuck, depress Trigger 12 several times and lubricate the tool through the air inlet. If this is unsuccessful, dismantle, clean, and lubricate the trigger components.
C
Christopher LynchAug 27, 2025
Why Stanley Rivet Tools mandrel breakage?
- H
  Heather TurnerAug 28, 2025
  Mandrel breakage in your Stanley Rivet Tool can occur due to excessive stroke or pressure; reduce both to prevent this. Additionally, a side load on the Mandrel can cause it to break, so ensure you hold the tool square to the application.
J
Jennifer DunlapAug 27, 2025
What to do if Stanley Rivet Tools is jammed?
- K
  Kenneth KramerAug 27, 2025
  If your Stanley Rivet Tool is jammed, it might be due to excessive stroke or excessive pressure, so reduce both. Another cause might be a defective Blind Rivet Nut or Mandrel A. In this case, press Manual Reverse 22 or alternately use Pin Punch K to manually remove the Blind Rivet Nut.
J
Jennifer RamirezAug 25, 2025
Why Stanley Rivet Tools pneumatic motor runs slowly?
- M
  Melissa NelsonAug 26, 2025
  A slow-running pneumatic motor in your Stanley Rivet Tool can be caused by several factors. Check for air leaks from the motor, especially worn seals that may need replacement. Ensure that the air pressure is adequate; if it's low, increase it. Also, inspect for any blockages in the airway and clear any restrictions. Lastly, the Motor Vanes 6M might be jamming, so clean and lubricate them.
S
shari17Aug 23, 2025
What to do if Stanley Rivet Tools does not spin off?
- E
  evansdennisAug 23, 2025
  If your Stanley Rivet Tool isn't spinning off, it could be due to a few reasons. Start by checking if the Chuck Nut 14 is loose and tighten it. Ensure that you are pressing and holding the Trigger 12 for the entire cycle of the tool. Also, the tool might not be reaching the necessary pressure or stroke, so try reducing the pressure or stroke setting. Another potential issue is a stuck Distributor 21A, which can be resolved by lubrication. Lastly, if the Air Motor is jammed, lubricate the tool at the air inlet; if that doesn't suffice, dismantle and clean it thoroughly.