Stannah MIDILIFT SL - User Manual

Other manuals for Stannah MIDILIFT SL

Installation Guide66 pages

Questions and Answers

A
Antonio ParsonsAug 9, 2025
What to do if my Stannah Indoor Furnishing lift will not ascend?
- V
  Veronica LoveAug 9, 2025
  If your Stannah Indoor Furnishing lift won't ascend, there could be several reasons: * A circuit breaker or the mains switch might have tripped; in that case, reset and turn on all three switches. * The isolation keyswitch might be off; reset and turn it on. * The door might not be fully closed or locked; ensure it's closed and locks are fully engaged, removing any obstructions. * The carriage or platform safety edge may be operated or sticking; remove any obstructions. * The motor overload in the pump unit might have tripped; turn it on and reset. * The platform might be overloaded; remove excess load. * The shut-off valve might be closed; open the valve, check the platform load, and adjust the valve if required.
N
Nicholas CopelandAug 15, 2025
What to do if my Stannah Indoor Furnishing lift will not descend?
- A
  Andre AllenAug 15, 2025
  If your Stannah Indoor Furnishing lift won't descend, consider these potential causes: * The door might be open; close the door, lower the lift manually, and reset the switch. Also, remove any excess load. * The ultimate limit might be operated, meaning there's no 24V power to the valve. * The platform might be overloaded; remove excess load. * The down solenoid valve might not be operational or the rupture valve at the base of the ram might be activated; check the system is working correctly and raise the lift to release the rupture valve.
M
murphythomasAug 21, 2025
Why does my Stannah Indoor Furnishing lift stop below the upper floor level?
- H
  huntsusanAug 21, 2025
  Your Stannah Indoor Furnishing lift might stop below the upper floor level if the up stopping switch has been activated. In this case, you should adjust the switch as required. Alternatively, the journey timer might have tripped; reset it and adjust if necessary.
B
Benjamin RichardsAug 27, 2025
Why does my Stannah Indoor Furnishing lift stop above the lower floor level?
- C
  Cheryl JohnsonAug 27, 2025
  If your Stannah Indoor Furnishing lift stops above the lower floor level, it might be because the down stopping switch has been activated. Adjust the switch as needed.
C
cartertamaraSep 2, 2025
How to fix a Stannah Indoor Furnishing door that will not open?
- M
  Mrs. Lauren Baxter MDSep 2, 2025
  If the door of your Stannah Indoor Furnishing won't open, it might be because the lift is not in the door zone. Call the lift to the floor level and adjust as required.

Summary

INTRODUCTION

Important - please read

Lift Safety - Your Responsibilities

Explains legal obligations for lift maintenance, thorough examination, and general safety.

SAFETY INSTRUCTIONS

MIDILIFT GL;SL PLATFORM LIFT

Lift Operation From The Platform

Lift Lowering Procedure

Step-by-step guide for manually lowering the lift platform in an emergency.

MIDILIFT SLPLUS CABIN LIFT

Manual Lowering Of The Cabin

Step-by-step guide for manually lowering the lift cabin in an emergency.

MIDILIFT XLPLUS CABIN LIFT

Lift Operation From The Landing

Keyswitch Operation

Lift Operation From The Cabin

Safety Edges

Power Loss Operation

Emergency Releasing Passengers

Procedure for trained personnel to safely release passengers in an emergency.

Manual Lowering Procedure

Step-by-step guide for manually lowering the lift in an emergency.

Passenger Release Procedure

Steps to release passengers after the lift has been manually lowered.

LIFT CARE

TROUBLESHOOTING

WARRANTY PROMISE

Our Guarantee

Warranty Conditions

Stannah MIDILIFT SL Specifications

General

Category	Lifting Systems
Brand	Stannah
Model	MIDILIFT SL
Travel Speed	0.15 m/s
Compliance	EN 81-41
Platform Width	900mm / 1100mm
Platform Depth	1400mm
Operating Temperature	0°C to +40°C