STL Striker Series - User Manual

To Next Page

2809 Business Park Dr • Buda • TX • 78610

Phone

800.757.2581 •

Fax

844.894.2652 •

customerservice@speedtechlights.com

STL Striker®/Virtue® Interior LED Trac Series

Operation Manual and Instructions

Congratulations, you are the owner of a STL Striker®/Virtue® Interior LED Trac Series! Your bar is equipped with the latest technology and features

at the best value found industry wide, GUARANTEED. In addition to that, your purchase comes with the STL 5 Year Warranty against any manufac-

turer defects that may occur with your bar. So please read this document carefully and call Customer Service at 800-757-2581 Monday - Friday 8:30

AM - 4:30 PM central time if you need assistance. We are available and happy to help!

Warnings and Notices for Users and Installers

This document must be delivered to and read by the end user and installer as it serves to provide you with the required information for proper and

safe use of your STL product. Before operating this or any STL products the user and installer must read this manual all the way through. You will

nd important information in this manual that could prevent property damage and/or serious injury to the user and installer.

STL products are intended to alert pedestrians and other operators of the presence of personnel, the operation of emergency vehicles, an emer-

gency site, and any warning needs. This does not ensure that pedestrians or drivers will react, heed, or observe emergency warning signals. Nor

does the use of emergency signals grant or ensure you the right of way. It is your responsibility to make sure you can proceed safely before driving

against trac, entering an intersection, responding at a high rate of speed, or walking on or around trac lanes.

Your STL emergency vehicle devices should be tested daily to ensure the device and all its functions are operating correctly. If you experience a

malfunction contact STL’s Customer Service immediately for troubleshooting options, or a warranty or service claim. You must ensure sure that

the projection of the visual and audible signal is not blocked by vehicle components (i.e.: open trunks, visors, compartment doors), vehicles, other

obstructions, or people.

This is professional grade equipment and is intended for strict use by authorized personnel only. It is the user’s responsibility to understand and

obey all laws regarding emergency warning devices. You must know and be familiar with all applicable city, state, and federal laws and regulations

prior to the use of emergency vehicle warning devices.

SpeedTech Lights, Inc. assumes no liability for any loss resulting from the use of this warning device. Proper installation is vital to the performance

of the warning devices and safe operation of the emergency vehicle. Since the operator is under stressful environments the equipment must be

properly wired and mounted to ensure eectiveness and safety. Therefore controllers must be properly installed and placed within convenient

reach of the operator so eye contact with the roadway is never lost.

The eectiveness of your STL equipment is highly dependent upon correct mounting and wiring. Improper wiring and mounting of the warning

device will reduce the output and performance of the equipment. Emergency warning devices frequently require high electrical voltages and/

or currents. Properly protect and use caution around live electrical connections. Grounding or shorting of electrical connections can cause high

current arcing, which can cause severe personal injury and/or serious vehicle damage, including re.

Electromagnetic interference can be caused by many electronic devices used in emergency vehicles. To ensure that this doesn’t happen to you,

lightbars should be mounted a minimum of 12” - 34” from the radio antenna and do not power your equipment from the same circuit or share the

same grounding circuit with radio communication equipment. After installation, test all the vehicle’s equipment together to ensure everything

operates free of interference.

Driver and/or passenger airbags bags (SRS) will impact the way you mount your equipment. Any equipment installed in the deployment area of

the airbags will damage or dislodge the airbags and sensors. This will also reduce the eectiveness of the airbags to protect the passengers and

therefore these areas must be avoided. Installers must make sure that this equipment along with any parts, hardware, wiring, power supplies, and

switch boxes do not interfere with the airbags, SRS wiring, or sensors.

Need help?

Do you have a question about the STL Striker Series and is the answer not in the manual?

Summary

Operation Manual and Instructions

General Safety Warnings and Usage Guidelines

Provides essential safety information, usage restrictions, and operational guidelines for users and installers.

Important Points for Your Safety and Longevity

Key considerations for safe operation, proper maintenance, and maximizing the lifespan of the light bar.

Unpacking Your STL Product

Instructions on how to unpack the product and identify all included components.

Pre-Installation and Testing

Steps for bench testing the unit to ensure all features and parts are functional before installation.

Instructions for Mounting, Wiring, and Programming

Detailed guidance on mounting the light bar, connecting wires, and programming its functions.

Mounting Headliner Bracket

Instructions for attaching the adjustable or static brackets to the vehicle's headliner.

Mounting 360° Suction Cup Bracket

Steps for mounting the light bar using suction cup brackets, including L-Bracket option.

Mounting Suction Cup Details

Specific steps for attaching the suction cup mount hardware to the light bar track.

Surface Mount End Caps

Instructions for replacing the standard end cap with a surface mount end cap.

Direct Control Box Operation

Explanation of the functions and operation of the Direct Control Box for the light bar.

Wiring: Connecting Wires to Battery

Guidance on safely connecting the light bar power cables directly to the vehicle's battery.

Wiring: Connecting Wires to Control Box

Instructions for connecting the light bar's power harness to the Direct Control Box.

Wiring: Connecting Extension Cables

Procedures for connecting extension cables, including cutting and soldering wires.

Programming Flash Patterns

How to set and select flash patterns using the control box or manually.

Maintenance

Recommendations for cleaning and preserving the light bar's function and appearance.

The STL Striker®/Virtue® Interior LED Traffic Series is a professional-grade LED light bar designed for emergency vehicles, providing warning signals to pedestrians and other operators. Manufactured by SpeedTech Lights, Inc., this device is built with the latest technology and features, backed by a 5-year warranty against manufacturing defects. It is intended for strict use by authorized personnel and requires a thorough understanding of automotive electronic systems for proper installation and operation.

Function Description:

The primary function of the STL Striker®/Virtue® Interior LED Traffic Series is to provide visual warning signals. It is equipped with LED modules that can display various flash patterns, including left arrow, right arrow, and center out arrow patterns, as well as a general flash mode. The device also supports a steady burn mode and a random pattern mode. These signals are crucial for alerting others to the presence of emergency personnel, emergency vehicles, or an emergency site. The light bar is designed to be mounted inside a vehicle, either permanently or using suction cups, and is controlled via a direct control box or integrated into an existing switch box.

Important Technical Specifications:

The device operates using a power harness with eight colored leads. The wiring diagram specifies the function of each wire:

Green: Left Arrow
Blue: Right Arrow
Yellow: Flash Pattern
Purple: Flash Mode
Orange: Center Out Arrow
Grey: Slow/Fast
Brown: Power
*Black (Thick): Negative (main power cable)
*Red (Thick): Positive (main power cable)

All cables, except the Negative wire, are designed to contact +VDC. The system incorporates non-volatile memory, allowing it to recall the last selected flash pattern when powered on. Proper fusing is critical, and the manual explicitly states not to use a fuse with a higher amp rating than the initial fuse included and to avoid circuit breakers with STL products. Ground terminations should be made directly to the battery. The current carrying capacity of wires and fuses can be significantly reduced under high ambient temperatures, necessitating the use of SXL type wire in the engine compartment where higher heat resistance is required, in accordance with SAE J-1128.

Usage Features:

The STL Striker®/Virtue® series offers several user-friendly features:

Direct Control® Box: This optional control box simplifies operation with dedicated switches.
- Left On/Off Switch: Turns all LED modules in the light bar on or off.
- Flash Pattern Button: Cycles through various flash patterns with each press.
- Steady Burn Mode: Activated by holding the flash pattern button down for 3 seconds.
- Random Pattern Mode: Activated by holding the flash pattern button down for 5 seconds.
Mounting Options:
- Headliner Bracket: An adjustable bracket system (four pieces per side for adjustable, one solid piece for static) allows for secure mounting to the vehicle's headliner. The forked pieces attach to the back of the bar, pointing away from the LEDs, while rectangular pieces align with mounting locations for optimal fit.
- 360° Suction Cup Bracket: This bracket attaches to the end cap of the light bar using included hardware and suction cups. It can also be used as an L-bracket mount by simply not attaching the suction cups.
- Surface Mount End Caps: These allow for surface mounting by replacing the existing end caps.
Non-Volatile Memory: The device retains the last selected flash pattern, ensuring consistent operation upon power-up.
Wiring Flexibility: While a direct control box is recommended, the device can also be integrated into custom switch boxes by referencing the provided wiring diagram.

Maintenance Features:

To ensure the longevity and optimal function of the STL Striker®/Virtue® light bar, specific maintenance guidelines are provided:

Daily Inspection: Users should inspect and test the product daily to ensure it operates properly and is securely mounted. Any malfunctions should be reported to STL Customer Service immediately.
Cleaning: The light bar should only be cleaned with water (H2O) and a soft cloth.
- Avoid: Car washes (automatic or pressure washers), brushes, or chemicals that could scratch or damage the equipment.
Lens Replacement: Over time, clear lenses may yellow. Replacement lenses can be purchased by contacting STL Customer Service.
Wiring Integrity: Regular checks of wiring connections are recommended to prevent lost power, corrosion, or damage. Soldered connections with heat shrink are preferred for durability.
Airbag Clearance: Equipment must not interfere with airbag deployment areas, SRS wiring, or sensors to prevent damage or reduced airbag effectiveness.

Important Safety Precautions:

The manual emphasizes several critical safety warnings:

Professional Installation: Installers must have a good understanding of automotive electronic systems.
Drilling Precautions: When drilling, ensure no vehicle components (electrical wires, fuel lines, upholstery) are damaged. Deburr drilled holes and use grommets and silicone sealant for wire passages.
Wiring Safety: Never cut wires or work on the unit while connected to a power source. Protect live electrical connections and avoid high current arcing. Ensure proper grounding directly to the negative battery post. Do not allow positive and negative wires to touch.
Eye Safety: Never stare directly into the LEDs to prevent momentary blindness or eye damage.
Operational Safety: Do not activate or control equipment in hazardous driving conditions. Ensure the control box is installed within convenient reach without obstructing the roadway view.
Airbag Deployment Zones: Avoid installing equipment in airbag deployment areas to prevent serious personal injury.
Electromagnetic Interference: Mount light bars a minimum of 12"-34" from radio antennas and avoid powering equipment from the same circuit or sharing the same grounding circuit as radio communication equipment to prevent interference.