Strong SRT4355 - User Manual

Questions and Answers

J
Jeanne ScottAug 16, 2025
What to do if my Strong SRT4355 Receiver has no picture?
- E
  Eric LynnAug 16, 2025
  If your Strong Receiver shows no picture, it could be due to the receiver not getting a signal, incorrect tuner parameters, or the dish pointing in the wrong direction. Check the antenna cable, replace it if necessary, and ensure it's tightly connected to the receiver. Verify the tuner parameters in the System set-up menu are correct. Use a spectrum analyzer to check the signal strength and adjust your dish accordingly.
P
priscillarichAug 19, 2025
What to do when the Strong SRT4355 Receiver shows 'EEPROM ERROR' message?
- G
  Gabriel BanksAug 19, 2025
  If your Strong Receiver displays the 'EEPROM ERROR' message, you should change U4: EEPROM (24C64).
M
matthewpotterAug 21, 2025
What to do when 'Tuner connect Fail' message appears on Strong SRT4355 Receiver?
- C
  Christopher BuchananAug 21, 2025
  If the 'Tuner connect Fail' message appears on your Strong Receiver, and the power supplied to the Tuner is normal, then the Tuner must be changed.
M
Melissa ThompsonAug 25, 2025
What to do when 'NO SIGNAL' message appears on Strong SRT4355?
- T
  Tammy EdwardsAug 25, 2025
  If the 'NO SIGNAL' message appears on your Strong Receiver, and U19's (KA317) input voltage is low, change the SMPS. If changing the SMPS doesn't solve the problem, check U19 Voltage Line in SMPS.
M
michaelgarciaAug 28, 2025
Why is the remote controller for my Strong Receiver not working?
- L
  Linda SchroederAug 28, 2025
  If the remote controller for your Strong Receiver isn't working, it might be due to the batteries not being inserted correctly or being exhausted. Verify that the batteries are correctly inserted into the remote controller. If the batteries are exhausted, replace them.
J
joseph56Aug 31, 2025
What to do if the display on the front panel of my Strong Receiver does not light up?
- R
  robertfieldsAug 31, 2025
  If the display on the front panel of your Strong Receiver doesn't light up, the power cord might not be plugged in. Check that the power cord is securely plugged into the wall outlet.
K
Katrina SotoSep 2, 2025
What to do when the Strong SRT4355 Receiver shows 'FLUSH DRAM' message?
- M
  Miss Mallory Perez MDSep 2, 2025
  If your Strong Receiver displays the 'FLUSH DRAM' message, re-solder U7 (L64005) and U8 (KM416S1020). If the issue persists, change U7 (L64005).
H
hkochSep 6, 2025
What to do when 'CI CARD INITIALIZING NOW….' message is continually on screen of Strong Receiver?
- E
  Emily LeonardSep 6, 2025
  If the message 'CI CARD INITIALIZING NOW….' is continuously displayed on the screen of your Strong Receiver, perform the firmware download again.
R
Rebecca ConradSep 8, 2025
What to do if the front 7-segment display acts strangely on Strong SRT4355 Receiver?
- E
  emily21Sep 9, 2025
  If the front 7-segment display on your Strong Receiver is acting strangely, replace the front panel.
R
Robert JohnstonSep 12, 2025
What to do if a scratch happens on the video screen with audio noise or stop phenomenon on Strong Receiver?
- J
  Jack SanfordSep 12, 2025
  If a scratch occurs on the video screen accompanied by audio noise or the audio stops on your Strong Receiver, replace the tuner.