Why are my specimens uneven with the Struers Control Panel?
Uneven specimens can occur if the specimens are wider than the radius of the preparation disc. Try using smaller specimens. Also, check if the specimens are passing over the center of the disc; if so, reposition the horizontal position of the control panel.
What should I do if the column starts to turn on my Struers LaboForce-100?
If the column starts to turn, it's likely due to loose column screws. Tighten the screws immediately.
How to fix a vibrating specimen holder plate on a Struers Control Panel?
A vibrating specimen holder plate can be caused by either an unbalanced plate or loose screws. You can try the following: * Replace the specimen holder plate if it's unbalanced. * Tighten the specimen holder plate screws if they are loose.
What to do if the surfaces are being damaged in Struers Laboratory Equipment?
If the surfaces are being damaged when using Struers Laboratory Equipment, it could be due to several reasons. The specimen may have burrs or sharp edges that need to be removed. Alternatively, the force applied to the specimen might be too high, or the specimen area might be too small. Try removing burrs and sharp edges, and lower the applied force to resolve this issue.
How to fix 'process cannot be started' error in Struers Laboratory Equipment?
If the process cannot be started on your Struers Laboratory Equipment, and you are seeing error messages, it might be because the flexible specimen holder is too close to the surface. To fix this, try changing the force, using higher specimens, or changing the configuration.
What to do if pins are touching the surface on Struers Laboratory Equipment?
If the pins on the flexible specimen holder are touching the preparation surface while using Struers Laboratory Equipment, it's likely that the force setting is too high, or the specimens are too low. You can decrease the force or increase the specimen height.
Why is the polishing cloth life so short on Struers Laboratory Equipment?
If you are experiencing a short lifetime of the polishing cloth with your Struers Laboratory Equipment, it might be because the polishing cloth is too soft. Try using a harder polishing cloth.
What to do if specimens fall out of Struers Laboratory Equipment?
If the specimens fall out of the flexible specimen holder in your Struers Laboratory Equipment, it could be due to incorrect placement or insufficient force. Increase the force.
Why do specimens develop a pencil shape in Struers Laboratory Equipment?
If the specimens develop a pencil shape when using Struers Laboratory Equipment, it could be due to several reasons: incorrect placement, a sample area that is too small, a specimen that is too high, or a specimen geometry that is round and solid. Turn the specimen and repeat the step.
What causes pins to stick in Struers Laboratory Equipment?
If the pins on the flexible specimen holder get stuck to the bottom plate of your Struers Laboratory Equipment, it's likely because the flexible specimen holder is dirty. Clean the flexible specimen holder.
Defines the purpose and compatible equipment for LaboForce-100.
Lists general/specific precautions and explains hazard symbols like DANGER, WARNING, CAUTION.
Overview of the LaboForce-100 unit, its components, and front view diagram.
Basic operation steps like starting and stopping the machine.
Guidelines for preparing the unit for storage or shipping securely.
Steps for unpacking the unit and checking the box contents.
Procedures for mounting, electrical, and compressed-air connections.
Procedures for inserting and adjusting specimen holders and mover plates.
Steps to adjust the height of the specimen mover plate.
Procedure for adjusting the horizontal positioning of holders/plates.
Final steps to secure the specimen mover adjustment.
Instructions for setting up the flexible specimen holder.
Procedures for inserting and adjusting the flexible holder's height.
Procedure for horizontal adjustment of the flexible holder.
Using LaboDoser-100 and LaboDoser-10 with LaboForce-100.
Reference to finding information on noise and vibration levels.
Explanation of buttons, controls, and the touch pad on the panel.
Recommendations for daily, weekly, and mover head cleaning.
Procedure for emptying the water/oil filter.
Guidelines for service checks, repair, and obtaining parts.
Accessing machine status info and equipment disposal guidelines.
Table listing common errors, their causes, and recommended actions.
Classification of messages/errors and how to acknowledge them.
Detailed specifications for motor, environment, power, air supply, and dimensions.
References to block and air diagrams for the LaboForce-100.
FCC notice and compliance information for the device.
Disclaimer regarding errors, changes, and manufacturer's responsibility.
General| Brand | Struers |
|---|---|
| Model | LaboForce-100 |
| Category | Control Panel |
| Language | English |
To Next Page