Stulz UltraWater 120 basic

Questions and Answers

E
elijah26Aug 5, 2025
How to fix Stulz UltraWater 120 basic that does not switch on?
- J
  Joanna WardAug 5, 2025
  If your Stulz Water Filtration System isn't switching on, several factors could be at play. First, ensure the system is connected to the drinking water mains and the tap is turned on. Check that the inlet water pressure is at least 1 bar. Verify the transformer is plugged into a live socket. Also, the system will not start if the pressure tank is full; it needs to be roughly half empty. If these steps don't resolve the issue, the transformer, solenoid valve, intake pressure switch, or tank pressure switch may be faulty and require replacement.
A
Allison HintonAug 9, 2025
Why my Stulz Water Filtration Systems does not produce enough pure water?
- R
  Rachel FryAug 9, 2025
  If your Stulz Water Filtration System isn't producing enough pure water, it could be due to several reasons. The consumer might be using more water than the system's nominal throughput, in which case you should replace the system with a more powerful one. Extremely cold supply water can also cause this issue, requiring a more powerful system. Other potential causes include a faulty pressure pump (replace the pressure pump), a clogged prefilter (replace the prefilter insert), or reduced membrane throughput (replace the membrane; consider softened water or a hardness stabilization filter if the decline was rapid).
J
Jeffrey RangelAug 14, 2025
What to do if the pure water quality from Stulz Water Filtration Systems is too poor?
- J
  John FarrellAug 14, 2025
  If the pure water quality from your Stulz Water Filtration System is too poor, several factors could be responsible. A faulty water quality monitoring system may be the cause, so check or replace it. An extremely contaminated prefilter can also degrade water quality, so replace the prefilter insert. Additionally, if the pure water quality of the untreated water is too poor, consider installing a deionizer behind the membrane or choosing a system model with a higher retention rate. A blocked membrane can also affect water quality, requiring membrane replacement. If the membrane quality declined rapidly, consider using softened water or a hardness stabilization filter.
S
Sarah BautistaAug 18, 2025
Why Stulz UltraWater 120 basic does not switch off?
- Y
  ydillonAug 18, 2025
  Your Stulz Water Filtration System might not switch off if the consumer is still using water; the system switches off only when water use ceases and the pressure tank is full. Alternatively, a faulty tank pressure switch could be the reason; in this case, replace the tank pressure switch.
J
Julia PetersAug 22, 2025
What causes Stulz Water Filtration Systems to switch on and off rapidly?
- D
  David StricklandAug 22, 2025
  If your Stulz Water Filtration System is switching on and off in rapid succession, the pressure tank valve might be closed; try opening it. Alternatively, the pressure tank itself may be faulty and require replacement.
T
Thomas PooleAug 27, 2025
Why does Stulz UltraWater 120 basic Water Filtration Systems switch on by itself?
- R
  Rita WilliamsAug 27, 2025
  If your Stulz Water Filtration System switches on regularly even when no water is being used, a faulty non-return valve is likely the cause. Replacing the non-return valve should resolve this issue.
J
Jessica ThomasAug 30, 2025
Why is there no waste water flowing from my Stulz UltraWater 120 basic?
- L
  Linda KeyAug 31, 2025
  If no waste water flows during the operation of your Stulz Water Filtration System, check if the waste water hose (red) is kinked and remove the kink. If the hose is not kinked, the flow restrictor may be faulty and require replacement.