Supermicro X10SLM+-F - Ethernet Ports

Chapter 2: Installation
2-19
LE6
DIMM2
DIMM3
DIMM1
DIMM4
FAN2
FAN3
FAN4
FAN1
FANA
JBR1
JLED1
JWD1
JPG1
JPL3
JPL4
JPME1
JPME2
JPL2
JPL1
J19 - RESERVED
LE3
LE5
LE4
J8
JPW1
JPW2
J21
JI2C1
JI2C2
JL1
J31
J32
JS1
JS2
JS3
JUSB1
JPI2C1
JTPM1
U7
J12
J11
T-SGPIO1
T-SGPIO2
JSD1
JSTBY1
B1
JBT1
JF1
J14
SW1
MH8
MH7
MH1
MH6
MH5
NMI
X
JTPM1:TPM/PORT80
JBR1:BIOS RECOVERY
1-2:NORMAL 2-3:BIOS RECOVERY
1-2:ENABLE
JPUSB1:USB4/5 WAKE UP
2-3:DISABLE
LAN4
LAN3
1-2:ENABLE JPL2:LAN2
2-3:DISABLE
2-3:DISABLE
JPL4:LAN4
1-2:ENABLE
JPME2
1-2:NORMAL 2-3:ME MANUFACTURING MODE
2-3:ME RECOVERY
JPME1
1-2:NORMAL
COM2
USB1(3.0)
FF
1-2:RST
2-3:NMI
JWD1:WATCH DOG
USB8/9
USB12/13
JSD1:SATA DOM POWER
_LAN
IPMI
1-2:ENABLE 2-3:DISABLE
JPL3:LAN3
JPL1:LAN1
2-3:DISABLE
1-2:ENABLE
JPI2C1:PWR I2C
VGA
COM1
USB0(3.0)
JBT1:CMOS CLEAR
LAN2
JL1
LAN1
DIMMB2
DIMMA2
JI2C1/JI2C2
USB4/5
CPU SLOT6 PCI-E 3.0 X8/16
2-3:DISABLE 1-2:ENABLE
CPU
OFF:DISABLE ON:ENABLE
:CHASSIS INTRUSION
JF1
ON
LED
LED
PWR
HDD
NIC1
NIC2
OH/
X
RST
PWR
USB2/3(3.0)
I-SATA3
I-SATA4
I-SATA1
I-SATA0
I-SATA5
CPU SLOT5 PCI-E 3.0 X8
PCH SLOT4 PCI-E 2.0 X2/4(INX8)
DIMMB1
DIMMA1
JPG1: VGA
J18 - RESERVED
I-SATA2
SP1
A
C
Ethernet Ports
Two Gigabit Ethernet ports (LAN1/
LAN2) are located next to the VGA
Connector on the I/O back panel to
provide network connections. These
ports accept RJ45 type cables. Two
additional ports are available on the
X10SLM+-LN4F (LAN3/LAN4) for a
total of four ports.
Note: Please refer to the LED
Indicator Section for LAN LED
information.
LAN Ports
Pin Denition
Pin# Denition
1 P2V5SB 10 SGND
2 TD0+ 11 Act LED
3 TD0- 12 P3V3SB
4 TD1+ 13 Link 100 LED
(Green, +3V3SB)
5 TD1- 14 Link 1000 LED
(Yellow, +3V3SB)
6 TD2+ 15 Ground
7 TD2- 16 Ground
8 TD3+ 17 Ground
9 TD3- 88 Ground
(NC: No Connection)
A. LAN1
B. LAN2
C. LAN3
D. LAN4
B
D