Supermicro X10SLM+-F - ME Recovery and Mode Select

Chapter 2: Installation
2-33
Manufacture (ME) Mode Select
Close this jumper JPME2 to bypass SPI
ash security and force the system to
use the Manufacture Mode which will
allow the user to ash the system rm-
ware from a host server to modify system
settings. See the table on the right for
jumper settings.
ME Mode Select
Jumper Settings
Jumper Setting Denition
1-2 Normal (Default)
2-3 Manufacture Mode
ME Recovery
Jumper Settings
Jumper Setting Denition
1-2 Normal (Default)
2-3 ME Recovery
Management Engine (ME) Recovery
Set jumper JPME1 to select ME Firm-
ware Recovery mode, which will limit
system resource for essential function
use only without putting restrictions on
power use. In the single operation mode,
online upgrade will be available via Re-
covery mode. See the table on the right
for pin denitions.
LE6
DIMM2
DIMM3
DIMM1
DIMM4
FAN2
FAN3
FAN4
FAN1
FANA
JBR1
JLED1
JWD1
JPG1
JPL3
JPL4
JPME1
JPME2
JPL2
JPL1
J19 - RESERVED
LE3
LE5
LE4
J8
JPW1
JPW2
J21
JI2C1
JI2C2
JL1
J31
J32
JS1
JS2
JS3
JUSB1
JPI2C1
JTPM1
U7
J12
J11
T-SGPIO1
T-SGPIO2
JSD1
JSTBY1
B1
JBT1
JF1
J14
SW1
MH8
MH7
MH1
MH6
MH5
NMI
X
JTPM1:TPM/PORT80
JBR1:BIOS RECOVERY
1-2:NORMAL 2-3:BIOS RECOVERY
1-2:ENABLE
JPUSB1:USB4/5 WAKE UP
2-3:DISABLE
LAN4
LAN3
1-2:ENABLE JPL2:LAN2
2-3:DISABLE
2-3:DISABLE
JPL4:LAN4
1-2:ENABLE
JPME2
1-2:NORMAL 2-3:ME MANUFACTURING MODE
2-3:ME RECOVERY
JPME1
1-2:NORMAL
COM2
USB1(3.0)
FF
1-2:RST
2-3:NMI
JWD1:WATCH DOG
USB8/9
USB12/13
JSD1:SATA DOM POWER
_LAN
IPMI
1-2:ENABLE 2-3:DISABLE
JPL3:LAN3
JPL1:LAN1
2-3:DISABLE
1-2:ENABLE
JPI2C1:PWR I2C
VGA
COM1
USB0(3.0)
JBT1:CMOS CLEAR
LAN2
JL1
LAN1
DIMMB2
DIMMA2
JI2C1/JI2C2
USB4/5
CPU SLOT6 PCI-E 3.0 X8/16
2-3:DISABLE 1-2:ENABLE
CPU
OFF:DISABLE ON:ENABLE
:CHASSIS INTRUSION
JF1
ON
LED
LED
PWR
HDD
NIC1
NIC2
OH/
X
RST
PWR
USB2/3(3.0)
I-SATA 3
I-SATA 4
I-SATA 1
I-SATA 0
I-SATA 5
CPU SLOT5 PCI-E 3.0 X8
PCH SLOT4 PCI-E 2.0 X2/4(INX8)
DIMMB1
DIMMA1
JPG1: VGA
J18 - RESERVED
I-SATA 2
SP1
A. ME Recovery
B. ME Mode Select
A
B