Supermicro X10SLM+-F - DOM PWR Connector (JSD1); Standby Power Header

Chapter 2: Installation
2-27
LE6
DIMM2
DIMM3
DIMM1
DIMM4
FAN2
FAN3
FAN4
FAN1
FANA
JBR1
JLED1
JWD1
JPG1
JPL3
JPL4
JPME1
JPME2
JPL2
JPL1
J19 - RESERVED
LE3
LE5
LE4
J8
JPW1
JPW2
J21
JI2C1
JI2C2
JL1
J31
J32
JS1
JS2
JS3
JUSB1
JPI2C1
JTPM1
U7
J12
J11
T-SGPIO1
T-SGPIO2
JSD1
JSTBY1
B1
JBT1
JF1
J14
SW1
MH8
MH7
MH1
MH6
MH5
NMI
X
JTPM1:TPM/PORT80
JBR1:BIOS RECOVERY
1-2:NORMAL 2-3:BIOS RECOVERY
1-2:ENABLE
JPUSB1:USB4/5 WAKE UP
2-3:DISABLE
LAN4
LAN3
1-2:ENABLE JPL2:LAN2
2-3:DISABLE
2-3:DISABLE
JPL4:LAN4
1-2:ENABLE
JPME2
1-2:NORMAL 2-3:ME MANUFACTURING MODE
2-3:ME RECOVERY
JPME1
1-2:NORMAL
COM2
USB1(3.0)
FF
1-2:RST
2-3:NMI
JWD1:WATCH DOG
USB8/9
USB12/13
JSD1:SATA DOM POWER
_LAN
IPMI
1-2:ENABLE 2-3:DISABLE
JPL3:LAN3
JPL1:LAN1
2-3:DISABLE
1-2:ENABLE
JPI2C1:PWR I2C
VGA
COM1
USB0(3.0)
JBT1:CMOS CLEAR
LAN2
JL1
LAN1
DIMMB2
DIMMA2
JI2C1/JI2C2
USB4/5
CPU SLOT6 PCI-E 3.0 X8/16
2-3:DISABLE 1-2:ENABLE
CPU
OFF:DISABLE ON:ENABLE
:CHASSIS INTRUSION
JF1
ON
LED
LED
PWR
HDD
NIC1
NIC2
OH/
X
RST
PWR
USB2/3(3.0)
I-SATA 3
I-SATA 4
I-SATA 1
I-SATA 0
I-SATA 5
CPU SLOT5 PCI-E 3.0 X8
PCH SLOT4 PCI-E 2.0 X2/4(INX8)
DIMMB1
DIMMA1
JPG1: VGA
J18 - RESERVED
I-SATA 2
SP1
A. DOM PWR
B. Standby PWR
A
B
DOM PWR Connector (JSD1)
The Disk-On-Module (DOM) power
connector, located at JSD1, provides
5V (Gen1/Gen) power to a solid state
DOM storage device connected to one
of the SATA ports. See the table on the
right for pin denitions.
DOM PWR
Pin Denitions
Pin# Denition
1 5V
2 Ground
3 Ground
Standby Power Header
The Standby Power header is located
at STBY1 on the motherboard. See
the table on the right for pin deni-
tions.
Standby Power
Pin Denitions
Pin# Denition
1 +5V Standby
2 Ground
3 No Connection