Supermicro X10SLM+-F - Power, IPMI Heartbeat, and UID LEDs

Chapter 2: Installation
2-37
Onboard PWR LED Indicator
LED Status
Status Denition
Off System Off
On System on, or
System off and PWR
Cable Connected
Onboard Power LED (LE3)
An Onboard Power LED is located at LE3
on the motherboard. When LE3 is on, the
AC power cable is connected. Make sure
to disconnect the power cable before
removing or installing any component.
See the layout below for the LED location.
LE6
DIMM2
DIMM3
DIMM1
DIMM4
FAN2
FAN3
FAN4
FAN1
FANA
JBR1
JLED1
JWD1
JPG1
JPL3
JPL4
JPME1
JPME2
JPL2
JPL1
J19 - RESERVED
LE3
LE5
LE4
J8
JPW1
JPW2
J21
JI2C1
JI2C2
JL1
J31
J32
JS1
JS2
JS3
JUSB1
JPI2C1
JTPM1
U7
J12
J11
T-SGPIO1
T-SGPIO2
JSD1
JSTBY1
B1
JBT1
JF1
J14
SW1
MH8
MH7
MH1
MH6
MH5
NMI
X
JTPM1:TPM/PORT80
JBR1:BIOS RECOVERY
1-2:NORMAL 2-3:BIOS RECOVERY
1-2:ENABLE
JPUSB1:USB4/5 WAKE UP
2-3:DISABLE
LAN4
LAN3
1-2:ENABLE JPL2:LAN2
2-3:DISABLE
2-3:DISABLE
JPL4:LAN4
1-2:ENABLE
JPME2
1-2:NORMAL 2-3:ME MANUFACTURING MODE
2-3:ME RECOVERY
JPME1
1-2:NORMAL
COM2
USB1(3.0)
FF
1-2:RST
2-3:NMI
JWD1:WATCH DOG
USB8/9
USB12/13
JSD1:SATA DOM POWER
_LAN
IPMI
1-2:ENABLE 2-3:DISABLE
JPL3:LAN3
JPL1:LAN1
2-3:DISABLE
1-2:ENABLE
JPI2C1:PWR I2C
VGA
COM1
USB0(3.0)
JBT1:CMOS CLEAR
LAN2
JL1
LAN1
DIMMB2
DIMMA2
JI2C1/JI2C2
USB4/5
CPU SLOT6 PCI-E 3.0 X8/16
2-3:DISABLE 1-2:ENABLE
CPU
OFF:DISABLE ON:ENABLE
:CHASSIS INTRUSION
JF1
ON
LED
LED
PWR
HDD
NIC1
NIC2
OH/
X
RST
PWR
USB2/3(3.0)
I-SATA 3
I-SATA 4
I-SATA 1
I-SATA 0
I-SATA 5
CPU SLOT5 PCI-E 3.0 X8
PCH SLOT4 PCI-E 2.0 X2/4(INX8)
DIMMB1
DIMMA1
JPG1: VGA
J18 - RESERVED
I-SATA 2
SP1
A. Onboard PWR LED
B. BMC (IPMI) Heartbeat
C. UID LED
A
IPMI Heartbeat LED
A BMC (IPMI) Heartbeat LED is located
at LE5 on the motherboard. When LE5 is
blinking, BMC (IPMI) functions normally.
See the table on the right for more in-
formation.
BMC Heartbeat LED
Status
Color/State Denition
Green:
Blinking
BMC: Normal
B
C
Unit ID (UID) LED
See page 2-20 for details on LE4.