Supero X9SRA User Manual

2-32
X9SRA Motherboard Series User’s Manual
TPM Support Enable (JPT1)
JPT1 allows the user to enable TPM (Trust-
ed Platform Module) support to improve
data integrity and system security. See the
table on the right for jumper settings. The
default setting is Enabled.
TPM Support Enable
Jumper Settings
Jumper Setting Denition
1-2 (Default) Enabled
2-3 Disabled
T-SGPIO1
3-SGPIO1
7 1
3-SGPIO2
T-SGPIO2
I-SATA5
I-SATA4
I-SATA3
I-SATA2
I-SATA1 I-SATA0
JPTM1
SAS0 SAS1
SAS2 SAS3
SAS4 SAS5
17
JUSB1617
9
21
JFPAUDIO
JSTBY
1
3
B81 B82 A81 A82
PCIE4
JPCI3
JWF1
1
3
JCOM2
1
5
6
JCOM1
JUSB89
JUSB1011
1
7
JUSB1213
1
CPU1
JUSB45
JUSB23 JKBMS_USB01
JAUDIO1
JLAN2_USB67
BT1
+
PCIE1
PCIE2
DIMM2A
DIMM3A
DIMM4A
DIMM1B
DIMM2B
DIMM3B
DIMM4B
DIMM1A
JF1
JD1
JTAG1
6
1
REV:1.01
Tested to Comply
With FCC Standards FOR HOME OR OFFICE USE
DESIGNED IN USA
MAC
SAS CODE
BAR CODE
JPW2
PCIE6
1
JPI2C1
JBT1
JPW1
1
JSPDIF_OUT
1
JSPDIF_IN
JI2C2
1
JI2C1
1
1
JL1
1
JCF1
1
JOH1
DP2
31
JPME1
JPAC1
JWD1
JVR2
JPL2
JPUSB1
JPME_DBG
4
FANA
FAN3
FAN1
FAN2
FAN4
MH3
MH7
MH4
MH8
MH1
MH9
MH6
MH5
H*
Pin1:RAID_KEY_PCH
JRK1
Pin2:Ground
Pin3:PCH_DYN_SKU
:TPM/PRO80
OFF:By BIOS JFPAUDIO_EN1
ON:Force Enable
USB3.0 2/3
2-3:Normal
1-2:BIOS recovery
JPBIOS1
JPME_DBG
1-2:ME Debug
2-3:Normal
JPME1
1-2:ME recovery
2-3:Normal
SLOT6 PCI-E 3.0 X16
SLOT4 PCI-E 3.0 X16
SLOT2 PCI-E 3.0 X4(IN X8) SLOT1 PCI-E 2.0 X4(IN X8)
1-2:ENABLE
2-3:DISABLE
JPT1
USB12/13
USB10/11
COM1
1-2:ENABLE
JPAC1:AUDIO
2-3:DISABLE
AUDIO FP
HD AUDIO
USB6/7
USB3.0 0/1
USB2/3
USB0/1
X9SRA-6
1-2 ENable
Power
Flash
KB/MOUSE
JPUSB1:USB Wake Up
2-3 Disable
PWRI2C
JF1
RST
ON
PWR
PWR
FF
FAIL
HDD NIC
1 2
NIC
OH
LED
NMI
PWR
X
PWR LED
SPEAKER
1-3:
4-7:
JD1:
2-3:NMI
JWD1:Watch Dog
1-2:RST
LAN1 LAN2
USB4/5
INTRUSION
CHASSIS
OFF: SLAVE
ON: MASTER
JCF1:Compact Flash
Compact
USB8/9
Wake on Lan
COM2
OFF:DISABLE ON: ENABLE
I2C bus for PCI slot
JI2C1/JI2C2
SLOT5 PCI-E 2.0 X1
SLOT3 PCI 33MHZ
CLOSE 1st
OPEN 1st
A
B
CF Slave/Master
Jumper Settings
Jumper Setting Denition
Open Slave
Closed Master
CF Card Master/Slave (JCF1)
A Compact Flash Card Master/Slave Se-
lect Jumper is located at JCF1. Close this
jumper to enable Compact Flash Card. For
the Compact Flash Card or the Compact
Flash Jumper (JCF1) to work properly, you
will need to connect the Compact Flash-
Card power cable to JWF1 rst. Refer tothe
board layout below for the location.
A. TPM Support Enable
B. CF Card Master/Slave Select

Supero X9SRA Specifications

General

Brand	Supero
Model	X9SRA
Category	Motherboard
Language	English