How to fix temperature fluctuation in Takagi T-KJr2-IN?
If you notice temperature fluctuations in the hot water from your Takagi Water Heater, check these: * Ensure the filter on the cold water inlet is clean. * Verify that the gas line is properly sized. * Confirm sufficient gas supply pressure. * Check for cross-connection between cold and hot water lines.
What to do if my Takagi Water Heater does not ignite?
If the unit does not ignite when water goes through your Takagi Water Heater, ensure the flow rate is over 0.75 GPM. Check the filter on the cold water inlet and inspect for reverse or cross-connections. If you're using a remote controller, verify that the power button is turned on. Also, check if the inlet temperature is too high.
What to do if hot water is not available from my Takagi T-KJr2-IN?
If hot water isn't available when you open a fixture with your Takagi Water Heater, consider the following: * Ensure the unit has a 120 VAC / 60 Hz power supply. * If using a remote controller, check if it's powered on. * Confirm the gas and water supply valves are fully open. * Check if the cold water inlet filter is clean. * Ensure the hot water fixture is open enough to draw at least 0.5 GPM through the heater. * Verify the unit isn't frozen. * For propane models, check if there's enough gas in the tank/cylinder.
Why is my Takagi Water Heater water not hot enough?
If the water from your Takagi Water Heater isn't hot enough, try these steps: * Compare the flow and temperature using the charts. * Check for cross-plumbing between cold and hot water lines. * Ensure the gas supply valve is fully open. * Verify the gas line is properly sized. * Confirm sufficient gas supply pressure. * Check if the set temperature is too low.
What to do if my Takagi T-KJr2-IN Water Heater water turns cold?
If the hot water from your Takagi Water Heater turns cold and stays cold, consider the following: * Ensure the flow rate is sufficient to keep the water heater running. * If a recirculation system is installed, check if the recirculation line has enough check valves. * Make sure the gas supply valve is fully open. * Check if the filter on the cold water inlet is clean. * Ensure the fixtures are clean of debris and obstructions. * Verify that the flow rate is not too low.
Why does the hot water from my Takagi T-KJr2-IN turn cold and stay cold?
If the hot water from your Takagi Water Heater turns cold and stays cold, ensure the flow rate is sufficient to keep the water heater running. If a recirculation system is installed, check that the recirculation line has enough check valves. Also, verify the gas supply valve is fully open and the filter on the cold water inlet is clean. Finally, make sure the fixtures are free of debris and obstructions, and check if the flow rate is too low.
How to fix fluctuation in hot water temperature from Takagi T-KJr2-IN?
If you experience fluctuation in hot water temperature with your Takagi Water Heater, start by checking if the filter on the cold water inlet is clean. Also, ensure the gas line is properly sized and the supply gas pressure is sufficient. Lastly, check for cross-connection between the cold and hot water lines.
What to do if Takagi Water Heater water is not hot enough?
If the water from your Takagi Water Heater is not hot enough, compare the flow and temperature using the charts. Check for cross plumbing between the cold and hot water lines. Ensure the gas supply valve is fully open and that the gas line is properly sized. Verify the gas supply pressure is adequate and that the set temperature is not set too low.
How to decrease time to get hot water from Takagi T-KJr2-IN?
If your Takagi Water Heater takes a long time to deliver hot water to the fixtures, it depends on the length of piping between the water heater and your fixtures. The longer the distance or the bigger the pipes, the longer it will take to get hot water. If you would like to receive hot water to your fixtures quicker, you may want to consider a hot water recirculation system.
Why is the water from my Takagi T-KJr2-IN Water Heater too hot?
If the water from your Takagi Water Heater is too hot, check if the set temperature is set too high.
Detailed technical specifications for the water heater models.
Outlines crucial safety precautions and definitions for installation and use.
Covers general installation, clearances, venting, gas, water, and electrical connections.
Guidelines for safe and compliant venting of exhaust gases from the unit.
Details on gas supply, pipe sizing, pressure, and electrical wiring for safe operation.
Steps to follow for the initial startup and safe operation of the water heater.
Essential safety information and instructions for operating the water heater.
Guidelines for normal use, including temperature settings and flow rates.
How to set the desired water temperature using dipswitches or a remote controller.
Details on the unit's freeze protection and how to prepare for long-term non-use.
Procedures for routine maintenance, filter cleaning, and diagnosing common issues.
Explains how error codes are displayed and their meanings for troubleshooting.
Exploded views of the water heater's internal and external components.
A comprehensive list of all available parts with item numbers and descriptions.
Terms and conditions of the product's limited warranty coverage.
General| Fuel Type | Natural Gas |
|---|---|
| Flow Rate | Up to 6.6 GPM |
| Heating Capacity | 140, 000 BTU |
| Energy Efficiency | 82% |
| Energy Factor | 0.82 |
| GPM @ 45°F Rise | 6.6 GPM |
| GPM @ 70°F Rise | 4.2 GPM |
| Minimum Flow Rate | 0.5 GPM |
| Water Connection | 3/4" NPT |
| Maximum Temperature | 167°F |
| Type | Tankless Water Heater |
| Maximum BTU | 140, 000 BTU |
| Dimensions | 20.1 in. H x 13.8 in. W x 6.7 in. D |
| Weight | 28 lbs |
| Warranty | 5-year parts |
| Temperature Range | 99°F to 167°F |
| Gas Connection | 3/4 inch |
| Vent Size | 3" |
| Venting | Direct Vent |
| Minimum BTU | 19, 500 BTU |
To Next Page
