Taylor c713 - Service Manual

Other manuals for Taylor c713

Original Operating Instructions52 pages

Operator Training46 pages

Questions and Answers

L
Linda CardenasSep 23, 2025
What does the 'Product Door Off' message mean on my Taylor c713 Freezer?
- R
  ryanwilkinsonSep 23, 2025
  If your Taylor Freezer displays a Product Door Off message, it could be caused by: * The door being off or loose. Install the door and tighten the hand screws. * A faulty door switch. Replace the switch. * The door switch not being properly installed. Ensure the door switch is fully inserted. * A faulty 24V relay. Replace the relay. * Low voltage from the 24V transformer. Check the power supply connections, shorts, and replace the transformer if necessary.
C
clarkdennisAug 23, 2025
Why does my Taylor Freezer run long cycles and shut off on the safety timer?
- L
  Lori SnyderAug 25, 2025
  If your Taylor Freezer is operating for extended periods and cycling off on the 11-minute safety timer, the issue could stem from several factors: * A dirty condenser. Clean the condenser. * Worn scraper blades. Replace the scraper blades. * A shortage of refrigerant. Repair the leak and recharge the machine. * Air in the system. Purge and recharge the system. * High overrun product (C712). Check the pump operation for the correct air/mix ratio.
R
Rachel HumphreyAug 25, 2025
Why is the head pressure too high in my Taylor c713 Freezer?
- K
  Kyle RamseyAug 26, 2025
  If the head pressure of your Taylor Freezer is too high, it could be due to several reasons: * The condenser might be dirty; if so, clean it. * The water valve might be out of adjustment or restricted; if so, check the adjustment and the water supply. * There might be insufficient air space around the machine; if so, ensure sufficient air space. * There might be a refrigerant overcharge; if so, correct the refrigerant charge. * The blower might be faulty; if so, replace the blower.
J
Jose FarleyAug 26, 2025
What to do if the product from my Taylor c713 is too soft?
- R
  Robin McmillanAug 26, 2025
  If your Taylor Freezer is dispensing product that is too soft, consider the following possible causes: * Insufficient air space around the machine. Ensure a minimum of 3” clearance on all sides and install the deflector. * Worn scraper blades. Replace the scraper blades. * Dirty air-cooled condenser. Clean monthly. * Outdated mix. Use fresh mix. * Refrigerant shortage. Locate and repair the leak. * Product viscosity set too warm. Adjust the product viscosity. * Incorrect usage of the mix feed tube (C713). Follow the correct feed tube procedures and use of the air orifice.
B
Brian JohnsonAug 27, 2025
Why is there excessive mix leakage in my Taylor c713?
- A
  Amy WilliamsAug 27, 2025
  If you find excessive mix leakage through the rear of your Taylor unit into the drip pan, it could be due to: * A worn or missing drive shaft seal. If worn, nicked, or missing, replace the drive shaft seal. * Inadequate lubrication. Lubricate properly. * The drive shaft rotating forward. Check gear alignment.
C
Christopher RochaSep 16, 2025
What does it mean when my Taylor Freezer shuts off and produces a fault tone?
- E
  elizabeth62Sep 16, 2025
  If your Taylor Freezer shuts off and produces a fault tone, it could be due to: * A fault alert. Check the fault screen in the operator's menu. * Insufficient air space. Allow 3” (76 mm) minimum clearance around all sides and install the deflector.
K
Kimberly JacksonSep 13, 2025
What causes scored freezing cylinder walls in my Taylor Freezer?
- L
  lisafitzgeraldSep 13, 2025
  If the freezing cylinder walls of your Taylor Freezer are scored: * Bent beater assembly. Replace the beater. * Missing or worn front bearing. Install or replace the front bearing. * Scraper blades incorrectly installed. Install scraper blades over the appropriate securing pin on the beater assembly.
A
Alexander MooreSep 14, 2025
Why is the product 'popping' when drawn from my Taylor Freezer?
- C
  Charles HamiltonSep 15, 2025
  If the product is “popping” when drawn from your Taylor Freezer: * Draw rate set too fast. Set the draw rate at 5 oz. to 7-1/2 oz. of product per 10 seconds. * Pump assembled/lubed incorrectly (C712). Assemble the pump according to instructions in the Operator's Manual. * Freezer has been turned on and off several times. Place the unit in the OFF position only when necessary.
T
Tiffany Rowe MDSep 5, 2025
Why is product not being fed into the freezing cylinder of my Taylor c713 Freezer?
- R
  Randy MorrisonSep 5, 2025
  If your Taylor Freezer is not feeding product into the freezing cylinder, it could be due to: * Inadequate mix in the hopper (Mix-Out light is lit). Fill the hopper with mix. * Air/mix pump incorrectly assembled (C712). Assemble the pump according to instructions in the Operator's Manual. * Air/mix pump is not operating (C713). Follow the correct feed tube procedures and use of the air orifice.
H
hdavenportSep 3, 2025
Why is the draw valve leaking on my Taylor c713 Freezer?
- B
  Bryan WilliamsSep 3, 2025
  If your Taylor Freezer's draw valve is leaking, the following could be the reasons: * Worn or missing draw valve O-rings. Replace them regularly. * Inadequate lubrication on the draw valve O-rings. Lubricate properly. * The wrong type of lubricant is being used. Use the proper lubricant, such as Taylor Lube High Performance.

Summary

Section 1: Introduction

Safety

Essential safety precautions and warnings for operating and servicing the freezer.

Model C712 Specifications

Running Specifications

General Installation Instructions

Guidelines and procedures for safely and correctly installing the freezer unit.

Section 3: Troubleshooting

General Troubleshooting Guide

Common problems, probable causes, and remedies for freezer operation issues.

Electrical Troubleshooting Guide

Guide for diagnosing electrical issues based on component operation in different modes.

C712;C713 Electrical Troubleshooting Guide

Specific electrical troubleshooting steps for C712 and C713 models.

Bacteria Troubleshooting

Guidance on preventing and addressing bacteria contamination issues in the freezer.

Taylor c713 Specifications

General

Type	Soft Serve Freezer
Number of Flavors	2
Refrigeration System	Air or Water Cooled
Separate Hopper Refrigeration	Yes
Indicator Lights	Yes
Water Cooled	Yes
Electrical	208-230V, 1PH, 50/60Hz
Motor	Two 1.5 HP
Air Cooled Minimum Clearance	6" on both sides