Taylor C712 - Service Manual

Other manuals for Taylor C712

Operating Instructions57 pages

Operator Training41 pages

Operator's Manual61 pages

Questions and Answers

J
Jessica VasquezSep 23, 2025
What does the 'Product Door Off' message mean on my Taylor Freezer?
- R
  Robert AlexanderSep 23, 2025
  If your Taylor Freezer displays a Product Door Off message, it could be caused by: * The door being off or loose. Install the door and tighten the hand screws. * A faulty door switch. Replace the switch. * The door switch not being properly installed. Ensure the door switch is fully inserted. * A faulty 24V relay. Replace the relay. * Low voltage from the 24V transformer. Check the power supply connections, shorts, and replace the transformer if necessary.
K
Kristina SullivanAug 23, 2025
Why does my Taylor Freezer run long cycles and shut off on the safety timer?
- M
  mendozajohnAug 23, 2025
  If your Taylor Freezer is operating for extended periods and cycling off on the 11-minute safety timer, the issue could stem from several factors: * A dirty condenser. Clean the condenser. * Worn scraper blades. Replace the scraper blades. * A shortage of refrigerant. Repair the leak and recharge the machine. * Air in the system. Purge and recharge the system. * High overrun product (C712). Check the pump operation for the correct air/mix ratio.
S
Samantha LongAug 25, 2025
Why is the head pressure too high in my Taylor Freezer?
- Z
  Zachary LoganAug 26, 2025
  If the head pressure of your Taylor Freezer is too high, it could be due to several reasons: * The condenser might be dirty; if so, clean it. * The water valve might be out of adjustment or restricted; if so, check the adjustment and the water supply. * There might be insufficient air space around the machine; if so, ensure sufficient air space. * There might be a refrigerant overcharge; if so, correct the refrigerant charge. * The blower might be faulty; if so, replace the blower.
A
Alan MyersAug 26, 2025
What to do if the product from my Taylor C712 is too soft?
- L
  Linda CurryAug 27, 2025
  If your Taylor Freezer is dispensing product that is too soft, consider the following possible causes: * Insufficient air space around the machine. Ensure a minimum of 3” clearance on all sides and install the deflector. * Worn scraper blades. Replace the scraper blades. * Dirty air-cooled condenser. Clean monthly. * Outdated mix. Use fresh mix. * Refrigerant shortage. Locate and repair the leak. * Product viscosity set too warm. Adjust the product viscosity. * Incorrect usage of the mix feed tube (C713). Follow the correct feed tube procedures and use of the air orifice.
A
Adam WolfAug 27, 2025
Why is there excessive mix leakage in my Taylor Freezer?
- R
  Robert SmithAug 27, 2025
  If you find excessive mix leakage through the rear of your Taylor unit into the drip pan, it could be due to: * A worn or missing drive shaft seal. If worn, nicked, or missing, replace the drive shaft seal. * Inadequate lubrication. Lubricate properly. * The drive shaft rotating forward. Check gear alignment.
F
fsteinSep 16, 2025
What does it mean when my Taylor C712 shuts off and produces a fault tone?
- T
  taylor23Sep 16, 2025
  If your Taylor Freezer shuts off and produces a fault tone, it could be due to: * A fault alert. Check the fault screen in the operator's menu. * Insufficient air space. Allow 3” (76 mm) minimum clearance around all sides and install the deflector.
D
david59Sep 13, 2025
What causes scored freezing cylinder walls in my Taylor C712 Freezer?
- M
  Mark JensenSep 13, 2025
  If the freezing cylinder walls of your Taylor Freezer are scored: * Bent beater assembly. Replace the beater. * Missing or worn front bearing. Install or replace the front bearing. * Scraper blades incorrectly installed. Install scraper blades over the appropriate securing pin on the beater assembly.
C
caroline54Sep 15, 2025
Why is the product 'popping' when drawn from my Taylor C712 Freezer?
- J
  Jennifer JohnstonSep 15, 2025
  If the product is “popping” when drawn from your Taylor Freezer: * Draw rate set too fast. Set the draw rate at 5 oz. to 7-1/2 oz. of product per 10 seconds. * Pump assembled/lubed incorrectly (C712). Assemble the pump according to instructions in the Operator's Manual. * Freezer has been turned on and off several times. Place the unit in the OFF position only when necessary.
R
rharrisSep 5, 2025
Why is product not being fed into the freezing cylinder of my Taylor Freezer?
- M
  monroekristopherSep 5, 2025
  If your Taylor Freezer is not feeding product into the freezing cylinder, it could be due to: * Inadequate mix in the hopper (Mix-Out light is lit). Fill the hopper with mix. * Air/mix pump incorrectly assembled (C712). Assemble the pump according to instructions in the Operator's Manual. * Air/mix pump is not operating (C713). Follow the correct feed tube procedures and use of the air orifice.
R
Richard SuarezSep 3, 2025
Why is the draw valve leaking on my Taylor Freezer?
- C
  Crystal MartinSep 3, 2025
  If your Taylor Freezer's draw valve is leaking, the following could be the reasons: * Worn or missing draw valve O-rings. Replace them regularly. * Inadequate lubrication on the draw valve O-rings. Lubricate properly. * The wrong type of lubricant is being used. Use the proper lubricant, such as Taylor Lube High Performance.