Why is the product from my Taylor C712 too stiff?
If the product from your Taylor Freezer is too stiff, consider the following: * Product viscosity set too cold. Adjust the product viscosity. * Incorrectly assembled or malfunctioning air/mix pump (C712). Re-assemble the pump or replace faulty components.
What to do if my Taylor C712 has no operation in any mode?
If your Taylor Freezer shows no operation when placed in any mode, check the following: * Ensure the machine is plugged in. * Verify the circuit breaker is on or replace the fuse if blown. * Confirm the power switch is in the ON position.
Why is the compressor not running on my Taylor C712 Freezer?
If the compressor of your Taylor Freezer isn't running, there are several potential causes: * The power switch might be off; if so, turn it on. * An incorrect keypad selection might have been made; if so, press the correct key for Auto operation. * The fuse or circuit breaker might have blown; if so, replace the fuse or turn on the breaker. * The contactor might be faulty; if so, replace it. * The compressor might have burned out; if so, replace it. * The overload might be tripped; if so, turn the power switch off, let the compressor cool, and then turn the power switch back on. * The reset might be off; if so, press the reset button.
What to do if no product is dispensed from my Taylor Freezer?
If your Taylor Freezer isn't dispensing product with the draw valve open in AUTO mode, possible causes include: * A plugged door spout. Break down the machine and dislodge the door spout clog. * The beater rotating counterclockwise. Correct the beater rotation to clockwise. * Inadequate mix in the hopper (mix out light is lit). Fill the hopper with mix.
Why is the draw valve leaking on my Taylor Freezer?
If your Taylor Freezer's draw valve is leaking, the following could be the reasons: * Worn or missing draw valve O-rings. Replace them regularly. * Inadequate lubrication on the draw valve O-rings. Lubricate properly. * The wrong type of lubricant is being used. Use the proper lubricant, such as Taylor Lube High Performance.
What causes low overrun in my Taylor C712?
If your Taylor Freezer is producing a low overrun, here are some possible causes: * Bad scraper blades. Replace the scraper blades. * Faulty air/mix pump components (C712). Inspect the air/mix pump components and replace any that are faulty. * Restricted air intake (air/mix pump) (C712). Clear the restriction. * Long ON cycles. Refer to problem 2 for solutions.
How to fix a plugged door spout on a Taylor C712?
If your Taylor Freezer has a plugged door spout, it could be due to: * Poor scraping. Replace the scraper blades. * Damaged draw valve O-rings. Replace the O-rings. * A damaged beater assembly. Inspect and replace if necessary. * A worn rear shell bearing. Inspect and replace if necessary.
Why is the liquid line hot on my Taylor C712?
If the liquid line of your Taylor Freezer is hot, it is likely due to a shortage of refrigerant. To fix this, repair the leak and recharge the system.
What causes low head pressure in a Taylor Freezer?
If the head pressure of your Taylor Freezer is too low, it is likely due to a refrigerant shortage. To resolve this, repair the leak and recharge the system.
Why is there excessive mix leakage in my Taylor Freezer?
If you find excessive mix leakage through the rear of your Taylor unit into the drip pan, it could be due to: * A worn or missing drive shaft seal. If worn, nicked, or missing, replace the drive shaft seal. * Inadequate lubrication. Lubricate properly. * The drive shaft rotating forward. Check gear alignment.
Essential safety warnings and guidelines for machine operation and maintenance.
Detailed technical specifications for both Model C712 and C713 freezers.
General installation instructions and an overview of the machine's user interface.
Explains the UVC control programming, initialization, and system data management.
Details on pump operation, timers, viscosity adjustments, and jumper pin configurations.
Covers software update procedures, fault descriptions, and system information access.
Presents the refrigeration schematic and lists key system components.
A comprehensive table of common problems, causes, and remedies for machine issues.
Guides for diagnosing and resolving electrical faults in various operating modes.
Specific troubleshooting for pump operation and bacteria contamination issues.
Details the warranty for parts and provides an overview of part identification.
Visual breakdowns of parts for Model C712 and Model C713.
Lists components accessible or replaceable by the operator for both models.
Identification of control boards, boxes, and related electrical components.
Details on pump assemblies, door/beater units, and other mechanical parts.
Lists optional accessories, cleaning supplies, and maintenance items.
Electrical schematics detailing the wiring for Model C712.
Electrical schematics detailing the wiring for Model C713.
To Next Page
General
