Why is the product 'popping' when drawn from my Taylor Freezer?
If the product is 'popping' when drawn from your Taylor Freezer, the draw rate may be set too fast; set it at 5 - 7 1/2 ounces of product per 10 seconds. Also, turning the freezer on and off repeatedly can cause this, so only place the unit in the 'OFF' position when necessary.
Why is my Taylor C723's product too soft?
If the product from your Taylor Freezer is too soft, several factors could be responsible. Ensure there's sufficient air space around the unit. Replace bad scraper blades and clean the air-cooled condenser monthly. Use fresh mix and check for a refrigerant shortage, repairing any leaks. Also, adjust the product viscosity if it's set too warm, and follow the correct feed tube procedures, including the use of the air orifice.
What to do if my Taylor C723 Freezer is not dispensing product even when the draw valve is open and the machine is in 'AUTO' mode?
If your Taylor Freezer isn't dispensing product when the draw valve is open and the machine is in 'AUTO' mode, the door spout may be clogged; you'll need to disassemble the machine to clear it. Another possibility is that the beater is rotating counterclockwise, so correct the beater rotation to clockwise. Finally, check the mix level in the hopper, as the mix out light might be lit, indicating it needs to be filled.
Why does my Taylor C723 Freezer operate long and cycles off on the 11 minute safety timer?
If your Taylor Freezer operates for extended periods and cycles off on the 11-minute safety timer, it could be due to a dirty condenser, which requires cleaning. Worn scraper blades should be replaced. Also, there might be a shortage of refrigerant, necessitating a leak repair and recharge of the unit, or air in the system, which requires purging and recharging.
What to do if my Taylor Freezer shows a 'Product Door Off' message?
If your Taylor Freezer displays a 'Product Door Off' message, first check if the door is off or loose; if so, install the door and tighten the hand screws. If the door is properly installed, the door switch might be faulty and need replacement. Ensure the door switch is fully inserted. In some cases, the 24V relay could be faulty, requiring replacement, or there might be low voltage from the 24V transformer, necessitating a check of the power supply connections and potential transformer replacement.
What causes a 'Compressor on too long' fault message on my Taylor C723?
A 'Compressor on too long' fault message on your Taylor Freezer can be caused by several factors. The draw rate might be set too fast, so adjust it to 5 - 7 1/2 oz. of product per 10 seconds. Inadequate air flow can also cause this, so ensure sufficient air space around the unit. A faulty blower baffle might be the issue, requiring repair or replacement. Finally, inadequate AXV settings can contribute, so set the AXV at the proper setting.
What to do if the mix in the hopper of my Taylor C723 Freezer is too warm?
If the mix in the hopper of your Taylor Freezer is too warm, the temperature is out of adjustment. You should adjust the hopper temperature.
Why is the product from my Taylor Freezer too stiff?
If the product from your Taylor Freezer is too stiff, it's likely that the product viscosity is set too cold. Adjust the product viscosity to correct this.
Why is the head pressure too low in my Taylor C723 Freezer?
Low head pressure in your Taylor Freezer is typically due to a refrigerant shortage. Repair the leak and recharge the system to resolve this issue.
Why does my Taylor Freezer have low overrun?
Low overrun in your Taylor Freezer can be caused by bad scraper blades, which should be replaced. It can also be caused by long “ON” cycles, see problem #2.
Safety precautions for installing the machine.
Reviewing the installation area for hazards.
Guidelines for safe electrical connections.
Safety precautions and information regarding refrigerant.
Critical safety warnings and operational guidelines.
Further safety warnings, handling instructions, and operational restrictions.
Guidelines for safe operation, machine placement, and environmental factors.
Accessing and navigating the manager's menu with access code.
Step-by-step guide for assembling the machine's internal parts.
Detailed steps for sanitizing the machine and its parts.
Procedure for priming the freezer with fresh mix.
Detailed steps for manual brush cleaning of parts.
Precautions and procedures for winter storage.
Troubleshooting problems with product dispensing.
Troubleshooting mix temperature and operational problems.
Lists items not covered by the equipment warranty.
General| Type | Soft Serve Freezer |
|---|---|
| Mix Flow | Gravity |
| Number of Flavors | 2 + Twist |
| Electrical | 208-230/60/1 |
| Freezing Cylinder Size | 3.4 qt (3.2 L) |
To Next Page
