Technics RS-B655 User Manual

"Memory
repeat" indicator
By simply designating
the beginning
("0000')
and the end
of the
part
that
you
want
to
play
repeatedly,
that
part
can be
repeatedly
played
for as many
as
16
times.
(This
repeat-play feature
can
be used only in the
playback
mode.)
I
I
Press
the
playback
button.
(The playback
indicator
will illuminate,
and
playback
will
begin.)
2
Press
the
counter-reset
button
at the
place
(A)
where
you
want
the repeat
play
to stan.
(The
counter will
be reset
to "0000".)
\t
Press
the
memory-repeat
button
at the
place
(B)
where
you
want
the repeat
play
to
end.
(The
memory-repeat
indicator
will illuminate.)
When
the memory-repeat
button is
pressed,
the
tape will
be
rewound
to
point
(A),
and the repeat
play
will
then begin.
volume
control
I
I
Set the headphones volume
control to low
posltion
before
connecting
headphones.
Z
Connect headphones
(not
included)
to the headphones
jack.
\t Use
the headphones
volume
control to adjust the volume
while
listening to music.
Plug
type: 6 mm
(%") phone plug,
stereo type.
Note:
Avoid listening
for
a
long
time that it irritates
the ears.
The unit is
equipped with the
automatic-tape-select
feature;
it
automatically
detects the type ol tape being used, and then makes
the suitable
adjustments accordingly of the bias and
equalization.
(The
tape-select indicator
will illuminate.)
Place where
counter-reset
button was
pressed
A:
"0000"
Place
where memory-repeat
button was
pressed
B
I
Tape
Repeat
play
(16
times) of this
part
)To
cancel the repeat-play function
before
it
stops
(after
16
repeats),
press
the memory-repeat
button.
(The
memory-repeat indicator
will
switch OFF.)
)To change the
setting of
point (B),
first
cancel the repeat-play
operation
(see
above),
and then
press
the memory-repeat
button
at the new
place.
Notes:
oThe
repeat-play
function will
be cancelled
if the
stop bufton or the
rewind/fast-foryvard/search
button is
pressed
during
repeat
play.
To
stop temporarily,
press
the
pause
button.
.Repeat
play
is
possible
while
either
the tape counter
or lhe linear
counter
is
displayed,
but a change from
one
to
the other cannot
be made while repeat
play
is
in
progress.
.lf,
after setting
point (A),
the tape is rewound
to set
point
(B),
the
repeat
play
will
be of the
part
between
the tape beginning
and
point (B).
(The
linear
counter
reading will
be a minus reading.)
Tape
Repeat
play
(16
times)
of this
part
oThere
may
be a slight ditference
(maximum
+4
seconds)
between the
settings made for
points (A)
and
(B)
and the
points
at
which
the tape is
actually
played
during repeat
play.
L
-9-

Technics RS-B655 Specifications

Power

power consumption	21 W
power supply frequency	50 Hz/60 Hz
power supply voltage	240 V

Audio Specifications

wow and flutter	0.05% (wRMS)
frequency response (Normal)	20 Hz-18 kHz
frequency response (CrOz)	20 Hz-18 kHz
frequency response (Metal)	20 Hz-19 kHz
S/N ratio (Dolby C NR on)	74 dB
S/N ratio (Dolby B NR on)	66 dB
S/N ratio (Dolby NR off)	56 dB

Weight and Dimensions

dimensions	430x135x290 mm
weight	4.9 kg