Technics SA-GX910 User Manual

aren
5 Set the center frequency level (flashing bar) to
+10
dB.
The illustration shown below is an example for EQ1.
-o ‘
tot
00 #0 402 630 he 18k 25K ak 63K Ok 128i 1K Med
wo
see 7B.
\
Pr)
¢
6 Select the preferred slope, “narrow” or
“wide”.
The curve slope selection changes trom “narrow” to wide"
each time this button is pressed.
The illustration shown below is an example for EQ1,
When "narrow" Is selected:
aly
‘ Cy
400 630 tk VOh 25k 4k O.3k 10k I2SK Wk tite)
x
Fine
adjustment
of
the
center
frequency
In step 7 above, press the fine mode select button to select the
desired center frequency while watching the parametric EQ
system center frequency display.
(The fine mode indicator will Illuminate and you will notice that the
frequency spectrum now has more resolution.)
Characteristics
of
center
frequency
40
Hz~63
Hz
This is the deep bass sound range. When this level is increased,
the sound quality of a bass guitar, drums, etc. will be stabilized for
a full, rich sound.
100 Hz~ 160 Hz
This is the bass sound range. When this level is increased, the
sound will seem to have a greater fullness and depth. indistinct
sounds can, moreover, be made distinct by lowering the level.
250 Hz~ 400 Hz
This range is the fundamental sound range. When this level is
increased, a forceful “punch” is added. This level adjustment is
also used to add additional richness to mate vocal sounds.
630 Hz~1 kHz
This is the range in which most of the vocal range of the human
voice is included. By increasing the control setting, vocal reproduc-
tions become more full of fife, and greater realism and ambience
can be added.
—27—
7
While
listening
to
the
sound
source,
select
the
desired
center
frequency.
See
the
“characteristics
of
center
frequency”
section
below
to
help
you
determine
the
desired
center
frequency.
To
select
the
center
frequency
more
precisely,
see
“Fine
adjustment
of
the
center
frequency”
below.
8
While
listening
to
the
sound
source,
readjust
the
level
as
required.
4g —P-EQTIONE—
» EO MODE
MANUAL
160 «
.
te t
0 250 400 O30 th tk 25k 4k GK 10k 128K 1k Di)
tN
nae see
-8-
9 Repeat steps 4—8 to adjust the center fre-
quency in the remaining bands.
Caution:
Extreme
{evel
adjustments
in
any
frequency
band
may
cause
damage to your receiver and/or your speakers.
“Ra coe
MANIA
———Fine mode
indicator
Parametric EQ
system center
frequency display
1.6 kHz~2.5 kHz
String instruments and wind instruments are in this range. When
this level is increased, their brilliance is emphasized for more
colorful sound.
4 kHz~6.3 kHz
This is the range for adjusting sound's luster and brightness.
When this level is increased, an additionat degree of brilliance and
color is added. For sounds which seem too metallic, on the other
hand, they can be softened by reducing the level.
10 kHz~ 16 kHz
This is the range in which finely subtle tones of radiance and spien-
dorous luminance can be added. By increasing the control setting,
an extra measure of glitter can be added, for example, to the
sounds of the cymbals, triangle, etc. This contro! can also be used,
by reducing its setting, to decrease annoying tape “hiss” noises.

Technics SA-GX910 Specifications

General

Brand	Technics
Model	SA-GX910
Category	Stereo Receiver
Language	English