TECO F510 series - Page 18

17
Group 03 External Digital Input and
Output Parameters
Code
Parameter
Name
Setting Range Default
Attribu
te
1: PWM (Pulse
Width
Modulation)
03-31
Pulse Inpu
t
Scaling
50~32000 1000 *1
03-32
Pulse inpu
t
gain
0.0~1000.0 100 *1
03-33
Pulse input
bias
-100.0~100.0 0.0 *1
03-34
Pulse input
filter time
0.00~2.00 0.1 *1
03-35
03-36
Reserved
03-37
Timer ON
Delay
(DI/DO)
0.0~6000.0 0.0
03-38
Timer OFF
Delay
(DI/DO)
0.0~6000.0 0.0
03-39
Relay (R3A-
R3C)
Output
Setting range
and definition
are the same
as those of 03-
11 and 03-12.
20
03-40
Up/down
Frequency
Width
Setting
0.00~5.00 0.00 *7
03-41
Torque
Detection
Level
0~150 10 *7
03-42
Delay Time
of Braking
Action
0.00~65.00 0.00 *7
03-43
UP/DOWN
Acceleration
/
Deceleratio
n Selection
0: Acceleration/
Deceleration
Time 1
0
Note1
1: Acceleration/
Deceleration
Time 2
03-44
Frequency
Detection
Level 2
0.0~400.0 0
Note2
03-45
Frequency
Detection
Width 2
0.1~25.5 2.0
Note2
03-46
Frequency
Detection
Level 3
0.0~400.0 0.0
Note2
03-47
Frequency
Detection
Width 3
0.1~25.5 2.0
Note2
03-48 Low Current
Detection
Level
0.0~999.9
0.1
Note3
03-49
Low Current
Detection
Delay Time
0.00~655.34
(Note6)
0.01
Note3
03-50 Frequency 0.0~400.0 0.0
Note4
Group 03 External Digital Input and
Output Parameters
Code
Parameter
Name
Setting Range Default
Attribu
te
Detection
Level 4
03-51
Frequency
Detection
Level 5
0.0~400.0 0.0
Note4
03-52
Frequency
Detection
Level 6
0.0~400.0 0.0
Note4
03-53
Current
A
gree Level
2
0.0~999.9 0.0
Note6
Group 04 External Analog Input and
Output Parameters
Code
Parameter
Name
Setting Range Default
Attribu
te
04-00
AI Input
Signal Type
0: AI2:
0~10V/0~20
mA
1
1: AI2:
4~20mA/
2~10V
04-01
AI1 Signal
Scanning
and Filtering
Time
0.00~2.00 0.03
04-02 AI1 Gain 0.0~1000.0 100.0 *1
04-03 AI1 Bias -100.0~100.0 0 *1
04-04 Negative AI
0: Disable
0
Note6
1: Enable
04-05
AI2
Function
Setting
0: Auxiliary
Frequency
0
1: Frequency
Reference
Gain
2: Frequency
Reference
Bias
3: Output
Voltage Bias
4: Coefficient
of
Acceleration
and
Deceleration
Reduction
5: DC Braking
Current
6: Over-Torque
Detection
Level
7: Stall
Prevention
Level During
Running