Index
Index- 20
CSA7000 Series, TDS7000 Series, & TDS6000 S eries Instruments User Manual
transition setup, C --8
width, C--7
width setup, C--8
Trigger overview, 3--71
Trigger point, defined, 3--41
Trigger setup, C--7
Trigger status lights, 3--82
Trigger T, 3--140, C--10
Trigger when
A Trigger, 3--108
A Trigger control window, 3--107, 3--110
transition is <, A Trigger control window, 3--103
transition time >, A Trigger control window, 3--103
Trigger, delayed, how to set up, 3--119
Trigger, glitch, how to set up, 3--94
Trigger, runt, how to set up, 3--96–3--122
Trigger, slew rate, how to set up, 3--101–3--122
Trigger, timeout, how to set up, 3--104
Trigger, width, how to set up, 3--99–3--122
Triggering
advanced, 3--74
advanced triggering, 3--88
comm triggering, 3--74, 3--122
define inputs, 3--109
define logic, 3--109
define the c lock source a nd edge , 3--111
define the da ta source, 3--111
delayed trigger system, 3 --78
edge, 3--73
glitch trigger, 3 --89
horizontal position, 3--77
logic trigger definitions, 3--91
overview of, 3--71
pattern trigger, 3--90
posttrigger, 3--73
pretrigger, 3 --73
runt trigger, 3--89
select glitch triggering, 3--94
select runt triggering, 3--96
select setup/hol d Triggeri ng, 3--110
select the polari ty, 3--96, 3--100
select the polarity and width, 3--94
select the source, 3--94, 3--96, 3--99, 3--101, 3--104
select timeout triggering, 3--104
select transition triggering, 3--101
select width triggering, 3--99
sequential triggering, 3--113
serial pattern triggering, 3--74, 3--122
set the data and clock levels, 3--111
set the level, 3--95, 3--100, 3--105
set the setup and hold times, 3--112
set the thresholds, 3--98
set the timer, 3 --105
set the transition time, 3--102
set thresholds, 3--109
set to trigger if width, 3--95
set to trigger when, 3--97, 3--100, 3--103, 3--104
set trigger when, 3--110
setup/hold trigger, 3--92
slope and level, 3--77
state trigger, 3 --91
the trigger event, 3--73
timeout trigger, 3 -- 90
to check trigger status, 3--82
to define a time qualified pattern trigger, 3--108
to define new trigger level prese ts, 3--86
to define pattern inputs, 3--106
to define the logic, 3--106
to force a trigger, 3--87
to select a preset trigger level, 3--85
to select the trigger mode, 3--81
to select the trigger slope, 3--79
to select the t rigger source, 3--80
to select the trigger type, 3--79
to set holdoff, 3--84
to set level, 3--79
to set mode and holdoff, 3--95, 3--99, 3--101, 3 --103,
3--105, 3--107, 3--110, 3--112
to set the trigger coupling, 3--81
to set thresholds, 3--106
to set to 50%, 3--80
to set trigger when, 3--107
to set up B Triggering, 3--121
to single trigger, 3--88
to trigger based on transition time, 3--101
to trigger on A (Main) only, 3--118
to trigger on a glitch, 3--94
to trigger on a pattern, 3 -- 106
to trigger on a runt pulse, 3--96
to trigger on a state, 3--109
to trigger on B After Time, 3 --119
to trigger on B Events, 3--120
to trigger on setup/hold time violations, 3--110
transition trigger, 3--90
trigger and horizontal delay summ ary, 3--117
trigger based on pulse timeout, 3--104
trigger based on pulse width, 3--99
trigger coupling, 3 --76
trigger holdoff, 3--75
trigger locat ion and level from display, 3--83
trigger modes, 3--74
trigger on a pattern, 3--105
trigger sources, 3--73, 3--114
trigger status from acquisition readout, 3--82
trigger status from trigger status lights, 3--82
trigger types, 3--73, 3--114
To Next Page
Loading...
