Teledyne 10 - Detector Assembly

88 pages

Save Page as PDF

To Next Page

To Previous Page

13BioOptix™ 10

Replacement Parts Lists

C-3

13BioOptix™ 10

Replacement Parts Li sts

C.1 Detector Assembly

Main Page

Table of Contents9
Section 1 Introduction13
Product Overview13
System Specifications14
Biooptix 10 Specifications14
System Controls and Connectors15
Biooptix 10 Front Panel Controls15
Biooptix 10 Front Panel15
Biooptix 10 Left-Side Controls and Connections16
Biooptix 10 Left-Side Connections16
Biooptix 10 Right-Side Connections17
Biooptix 10 Rear Panel Controls and Connections18
Section 2 Installation19
Unpacking the Biooptix 10 System19
Biooptix 10 Installation19
Biooptix 10 Location and Space Requirements19
Electrical Requirements20
Assembling the Biooptix 1020
System Space Requirements20
Accessing Pump and Column Module Internal Connections21
Removing the Column Module Back Plate21
Routing the Sample out Lines (Column Module)22
Pump Controller Connection22
P110 Connection on BD323
J106 Connection on BD123
AC Power Connection from Pump Module24
Ribbon Cable Connections (Top Half of Column Module Shown)24
Liquid Connections25
Aligning the Fasteners26
Column Clamps Inserted26
Assembling the Foxy 20027
Foxy Arm27
Fluid Connections28
Buffer Assembly Routes a Common Solution to All Ten Channels29
Buffer Assemblies Installed29
Tubing Color Chart30
Foxy 200 Tubing Connections31
Adhesive Retainers Attached31
Windows PC Connection32
Biooptix 10 Software Installation32
Configuring Biooptix 10 Software32
Windows ® PC Minimum Requirements32
Biooptix 10 System Preparation33
Column Bypass Tubing34
Mode Control Knob34
Biooptix 10 Manual Hardware Control Window35
Section 3 Operation37
Sample Preparation37
Column Installation37
Column Tubing and Adapters37
Biooptix 10 Software38
Overview38
Gradients38
Gradient File38
Defining a Gradient39
Saving the Gradient39
Methods39
Equilibrate Settings40
Equilibrate Tab Settings40
Load Settings41
Load Tab Settings41
Wash Settings42
Elute Settings42
Wash Tab Settings42
Elute Tab Settings42
Flush Settings43
Saving the Method File43
Experiments43
Flush Tab Settings43
Setting up the Experiment44
Editing the Experiment44
Experiment File44
Saving the Experiment File45
Running the Experiment45
System Operation45
Biooptix 10 Operation Buttons45
Operation Displays46
Suspending System Operation46
Pause at End of Block46
Post-Experiment Operation47
Pump Flush47
Flush Window47
Saving Run Data48
Autoreports49
Section 4 System Maintenance51
Periodic Maintenance51
Flush Window51
Exterior Cleaning52
Piston Seal Replacement52
Access the Pump Assembly53
Pump Assembly Components54
Attach Seal to Push Rod54
Deuterium Lamp Replacement55
Waste Port Mounting Plate56
Deuterium Lamp Location56
Troubleshooting57
Operating Problems57
Common Problems57
Leaks58
Electrical58
Inaccessible Fuses58
Inaccessible Breakers58
Circuit Breaker Location59
Thermal Breaker Location59
Service Department60
How to Ship Returns60
Appendix A Method Templates61
Opening the Template61
A-1 Installed Standard.tpl File62
Modifying the Template63
General Editing Rules63
A-2 Customizable Values in the Standard.tpl File63
Blocks64
Blockn64
Other64
Appendix B Fluid Path Diagrams65
Fluid-Type Blocks65
B-1 Fluid Path for Fluid-Type Blocks65
Load-Type Blocks66
Fluid Path for Load-Type Blocks66
B-2 Inactive Channel66
Pump Injections66
Gradient-Type Blocks67
Fluid Path for Load-Type Blocks - Manual Injections67
Pump Flush68
Plumbing Diagram68
B-7 Biooptix 10 Plumbing Diagram69
Appendix C Replacement Parts Lists71
Detector Assembly73
Column Module77
Pump Module81
Declaration of Conformity85

Teledyne 10 - Detector Assembly

Table of Contents

Related product manuals