What to do if my Tennant Floor Machine has poor scrubbing performance?
If your Tennant Floor Machine's scrubbing performance is lacking, start by checking the scrub brushes for any caught debris and remove it. Also, inspect the scrub brushes for wear and replace them if necessary. Using improper detergent or brushes can also cause this issue; consult with a Tennant representative for advice on the correct products.
Why is my Tennant Floor Machine's sweeping performance poor?
Poor sweeping performance in your Tennant Floor Machine can stem from several causes. Check the following: * Worn brush bristles: Replace the brushes. * Improperly adjusted main and side brushes: Adjust them correctly. * Debris caught in the main brush drive mechanism: Clear the debris. * Full hopper: Empty the hopper. * Worn or damaged hopper lip skirts: Replace the lip skirts. * Hopper dump door closed: Open the hopper dump door. If these steps don't resolve the issue, or if you suspect a main or side brush drive failure, it's best to call Tennant service personnel. Using the wrong sweeping brush may also cause this problem, so contact a Tennant representative for assistance.
How to fix little or no solution flow in my Tennant 8200D Floor Machine?
If your Tennant Floor Machine has little to no solution flow, start by checking if the solution tank is empty and fill it if necessary. Ensure the solution flow switch and ES switch are turned on. Also, inspect the solution supply lines for any blockages and flush them if needed. If the manual control valve is nearly closed, open it further to increase solution flow.
How to stop excessive dusting from my Tennant 8200D Floor Machine?
Excessive dusting from your Tennant Floor Machine could be due to several reasons. Check the brush skirts and dust seals for wear, damage, or misalignment, and replace or adjust them as needed. If the hopper dust filter is clogged, shake, clean, or replace it. A damaged vacuum fan seal should be replaced. If the Thermo Sentry has tripped, allow it to cool. Ensure the hopper dump door is open. If the vacuum fan has failed, call Tennant service personnel.
General| Brand | Tennant |
|---|---|
| Model | 8200D |
| Category | Floor Machine |
| Language | English |
Operational safety rules for machine use.
Alerts to potential hazards and risks during operation.
Location and meaning of machine safety labels.
Outlines the operator's duties for safe machine operation.
Identifies and labels the primary parts of the machine.
Explains the meaning of symbols used on controls and indicators.
Details the main controls and instrument panel layout.
How to use the directional pedal for travel and speed.
Explains the operation of the brake and parking brake pedals.
How to start the engine and operate the steering wheel.
Operation of main sweep brush levers and pressure knob.
Operation of side brush lever, handle, and hopper lever.
Overview of the control panel features and indicators.
How to activate and adjust scrubbing operations.
Operation of squeegee and optional edge scrub switches.
Function of the ES switch and recovery tank full indicator.
Operation of detergent flow and engine speed controls.
Operation of sweep vacuum fan and filter shaker switches.
Operation of lights and solution flow control switches.
Adjustment of the adjustable solution flow valve.
Explains charging, oil pressure, and water temperature lights.
Explains hopper temperature, OK, and clogged filter lights.
Explains hopper door closed and hydraulic filter bypass indicator lights.
Information on circuit breakers and fuses.
Adjusting standard, adjustable, and suspension operator seats.
Specific adjustment for the seat position lever.
Covers hopper support bar, gas springs, and latches.
Explanation of the machine's operational principles and flow.
A list of checks to perform before operating the machine.
Step-by-step instructions for starting the engine.
Guidance on sweeping and scrubbing techniques and brush types.
Procedures for performing sweeping tasks.
Steps to correctly end sweeping operations.
Instructions for safely emptying collected debris from the hopper.
Steps for filling the solution and detergent tanks.
Detailed instructions for performing scrubbing tasks.
Procedures for double scrubbing and ending scrubbing operations.
Steps for emptying and cleaning the machine's tanks.
Procedures for safely shutting down the machine after use.
A list of checks to perform after completing operation.
How to secure the hopper in a raised position using the support bar.
How to release the hopper support bar to lower the hopper.
Guidelines for operating on slopes and securing the machine for transport.
Common operational problems and their recommended solutions.
Schedule and guidelines for routine maintenance tasks.
Guide to lubricating critical machine components.
Procedures for engine oil, filters, and cooling system upkeep.
Lubrication for front wheel bearings, rear wheel support, and lift arm pivots.
Information on hydraulic fluid, filters, and hoses.
Maintenance of the engine's radiator and coolant system.
Procedures for checking and replacing air and fuel filters.
Care for the battery and tensioning of engine and accessory belts.
Importance and maintenance of the static drag chain.
Cleaning and maintenance of the hopper and its dust filter.
Step-by-step guide for removing and cleaning the hopper dust filter.
Information on inspecting and maintaining the scrub head and brushes.
Checking, adjusting patterns, and replacing the main sweep brush.
Checking and replacing the side brush and adjusting its pattern.
Step-by-step instructions for replacing scrub brushes.
Maintenance of the recovery tank and solution tank.
Procedures for leveling and adjusting the rear squeegee blade.
Adjusting and replacing side squeegee blades.
Checking and replacing various skirts and seals on the machine.
Information on service brakes, parking brake, tires, and rear wheel torque.
Guidelines for safely moving and transporting the machine.
Procedures for lifting the machine for service and preparing for storage.
Key physical dimensions and tank capacities of the machine.
Data on speed, turning, and incline capabilities.
Details on the engine type, displacement, and power output.
Information on the steering mechanism and hydraulic system components.
Details on the braking system and tire types and sizes.
Visual diagrams showing the machine's overall dimensions.
To Next Page
