Tennant T2 - User Manual

Other manuals for Tennant T2

Manual4 pages

Questions and Answers

V
Victoria GarciaAug 16, 2025
Why is my Tennant Scrubber not picking up water?
- M
  Michael HamiltonAug 16, 2025
  Poor water pickup in your Tennant Scrubber can occur due to several reasons. The recovery tank might be full and needs draining. Check for a loose drain hose cap and tighten it. The float shut-off screen in the recovery tank or the squeegee assembly might be clogged and require cleaning. Inspect the squeegee blades for wear and replace or rotate them if needed. Ensure correct squeegee blade deflection by adjusting the blade height. Secure any loose vacuum hose connections and remove any debris clogging the vacuum hose. If the vacuum hose is damaged, replace it. Make sure the recovery tank cover is properly positioned and replace the seal if damaged. Finally, low battery charge can cause this issue, so recharge the batteries.
M
meganlynnAug 18, 2025
Why is there little or no solution flow in my Tennant T2 Scrubber?
- J
  Jose JohnsonAug 18, 2025
  Little to no solution flow in your Tennant Scrubber may be due to a clogged solution tank filter or solution hose; clean the filter or flush the hose. A clogged solution valve can also be the culprit; remove and clean the valve. Check the solution flow control knob; it may be set too low, so adjust it. Also, check for a loose screw on the control knob; calibrate the knob and retighten the screw.
J
James JacksonAug 21, 2025
What to do if the brush motor will not operate on my Tennant T2?
- E
  Erik WagnerAug 21, 2025
  If the brush motor on your Tennant Scrubber won't operate, ensure the scrub head is lowered to the floor. If it is, check if the brush motor circuit breaker has tripped and reset it if necessary. For a faulty scrub head switch, control handle triggers, brush motor, wiring, or worn carbon brushes, it is recommended to contact Service Center.
M
Megan JohnsonAug 25, 2025
What to do if the vacuum motor will not operate on my Tennant Scrubber?
- D
  David VegaAug 25, 2025
  If the vacuum motor on your Tennant Scrubber won't operate, make sure the squeegee is lowered to the floor. If it is, check the vacuum motor fuse and replace it if blown (25 Amp fuse). For a faulty vacuum motor or wiring, or worn carbon brushes, it is recommended to contact Service Center.
E
Eric ConnerAug 30, 2025
What to do if Tennant Floor Machine vacuum motor will not operate?
- S
  Sara HudsonAug 30, 2025
  If the vacuum motor on your Tennant Floor Machine isn't working: * Make sure the squeegee is lowered to the floor. * Check the vacuum motor fuse; if it's blown, replace it with a 25 Amp fuse.
F
Frances JonesSep 2, 2025
What to do if my Tennant Scrubber machine will not operate?
- M
  matthewbullockSep 2, 2025
  If your Tennant Scrubber won't operate, there are several potential causes. First, check if the batteries are discharged and charge them if necessary. If the batteries are faulty, replace them. Ensure the battery cable is not loose and tighten it if it is. For a faulty key switch, it is recommended to contact Service Center.
T
Toni HuertaSep 5, 2025
What to do if Tennant Floor Machine brush motor will not operate?
- T
  Tara AguilarSep 5, 2025
  If the brush motor on your Tennant Floor Machine won't operate: * Ensure the scrub head is lowered to the floor. * Check if the brush motor circuit breaker has tripped and reset it if necessary.
M
martinlewisSep 9, 2025
How to solve little or no solution flow in Tennant Floor Machine?
- J
  Jennifer ScottSep 9, 2025
  If you're experiencing little to no solution flow with your Tennant Floor Machine: * The solution tank filter or hose might be clogged; clean the filter or flush the hose. * A clogged solution valve needs to be removed and cleaned. * The solution flow control knob might be set too low; adjust it. * If there's a loose screw on the control knob, calibrate the knob and retighten the screw.
M
Marcus DanielsSep 12, 2025
What to do if on-board battery charger will not operate in Tennant Floor Machine?
- J
  Jeremy GarzaSep 12, 2025
  If the on-board battery charger of your Tennant Floor Machine isn't working: * Check the plug connection to the power supply. * If the power supply cord is faulty, replace it.
V
virginiaboothNov 26, 2025
Why Tennant Floor Machine has poor water pickup?
- C
  Curtis BarajasNov 26, 2025
  Poor water pickup from your Tennant Floor Machine can occur due to several reasons: * The recovery tank might be full, in which case you should drain it. * The drain hose cap might be loose; tighten it. * The float shut-off screen in the recovery tank could be clogged, so clean it. * The squeegee assembly might be clogged; clean it. * Squeegee blades might be worn, so replace or rotate them. * Incorrect squeegee blade deflection can cause this issue, so adjust the squeegee blade height. * Loose vacuum hose connections should be secured. * A clogged vacuum hose needs to have the debris removed. * A damaged vacuum hose should be replaced. * Ensure the recovery tank cover is properly positioned. * Replace a damaged recovery tank cover seal. * Low battery charge, recha...

Summary

Safety Precautions

General Safety Warnings

Key warnings regarding fire, explosion, electrical hazards, and spinning parts.

Operational Safety Guidelines

Safety Labels

Machine Components

Machine Installation

Installing Batteries

Instructions and safety precautions for installing machine batteries.

Machine Setup

Installing Brushes;Pads

Filling Solution Tank

Machine Operation

Pre-Operation Checks

Essential checks to perform before starting the machine for operation.

Operating the Machine

Step-by-step instructions for starting, operating, and stopping the machine.

While Operating Machine

Important operational guidelines and warnings during machine use.

Draining Tanks

Draining Recovery Tank

Procedure for draining and cleaning the machine's recovery tank.

Draining Solution Tank

Charging Batteries

Using the On-Board Battery Charger

Guide to setting up and using the on-board battery charger correctly.

On-Board Battery Charger Fault Codes

Machine Maintenance

Daily Maintenance

Routine daily tasks to keep the machine in good working order.

Monthly Maintenance

Battery Maintenance (Lead Acid Batteries)

Storing Machine

Transporting Machine

Troubleshooting

Power and Charger Issues

Diagnosing issues with machine power and on-board battery charger.

Motor and Solution Flow Problems

Short Run Time

Specifications

Tennant T2 Specifications

General

Cleaning Path	17 in / 430 mm
Power Source	Battery
Sound Level	68 dBA
Battery Run Time	Up to 3 hours
Machine Type	Walk-Behind Scrubber
Brush Deck Width	17 in / 430 mm
Battery Voltage	24 V