EasyManua.ls Logo

Tennant T3 - User Manual

Tennant T3
105 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
ENGLISH - ESPAÑOL - FRANÇAIS
T3/T3+
Operator Manual
Manual De Operador
Opérateur Manuel
9004170
Rev. 04 (05-2010)
www.tennantco.com
Automatic Scrubber
Fregadora Automática
Balayeuse Automatique
*9004170*
(S/N 10372394- )
North America / International
The Safe Scrubbing Alternativer
Hygenic
R
Fully Cleanable Tanks

Table of Contents

Other manuals for Tennant T3

Preview: Operator And Parts Manual
Operator And Parts Manual124 pages
Preview: Use And Care Guide
Use And Care Guide2 pages
Preview: Product Guide
Product Guide12 pages

Questions and Answers

  • D
    David LewisSep 12, 2025
    Why is the FaST system not working on my Tennant Scrubber?
    • N
      Noah SmithSep 12, 2025
      If the FaST system on your Tennant Scrubber isn't working correctly, check the following: * Ensure the FaST system switch is turned on: Turn on the FaST system switch. * Verify the FaST-PAK supply hose is connected: Connect the supply hose. * Check if the FaST Pump fuse is blown: Replace the 7.5 Amp fuse. * Inspect for clogs in the FaST-PAK supply hose or connectors: Soak in warm water to unclog. * Confirm the FaST-PAK carton isn't empty: Replace the FaST PAK carton. * Check for kinks in the FaST-PAK supply hose: Undo any hose kinks. * Ensure that the solution tank filter isn't clogged: Drain the solution tank, remove the solution tank filter, clean it, and reinstall it.
  • R
    Rhonda CarterAug 23, 2025
    How to fix a Tennant T3 that won't turn on?
    • J
      Jesse BassAug 23, 2025
      If your Tennant Scrubber is not operating, there are several possible causes: * The batteries may be discharged: Charge the batteries. * The emergency-stop button may be activated: Turn the button clockwise to reset it. * There may be a loose battery cable: Tighten the loose cable. * The main fuse may be blown: Replace the fuse. * The batteries may be faulty: Replace the batteries. If none of these steps work, contact a service center.
  • S
    Sharon GardnerAug 25, 2025
    Why won't my Tennant Scrubber move?
    • N
      nathan26Aug 25, 2025
      If your Tennant Scrubber isn't moving, consider the following possibilities: * The parking brake may be set: Release the parking brake lever. * The main fuse may be blown: Replace the 30 Amp fuse. If these solutions do not resolve the issue, contact a service center.
  • A
    Anthony DelacruzAug 27, 2025
    What causes the vacuum motor to fail on a Tennant T3?
    • J
      Jennifer AdamsAug 27, 2025
      If the vacuum motor on your Tennant Scrubber is not working, check these potential causes: * The squeegee may be raised off the floor: Lower the squeegee. * The vacuum motor fuse may be blown: Replace the 25 Amp fuse. If these solutions do not resolve the issue, contact a service center.
  • C
    Charles HarrisAug 27, 2025
    How do I restore solution flow in my Tennant Scrubber?
    • B
      Brent JimenezAug 27, 2025
      If you're experiencing little to no solution flow in your Tennant Scrubber (Conventional Scrubbing), consider the following: * The solution tank filter or solution hose may be clogged: Clean the solution tank filter or flush out the solution hose. * The solution valve may be clogged: Remove the valve and clean it. * The solution flow control knob may be set too low: Adjust the solution control flow knob. * There may be a loose screw on the control knob: Calibrate the knob and retighten the screw.
  • C
    Clifford MatthewsNov 28, 2025
    What to do if Tennant Floor Machine has poor water pickup?
    • J
      jamessextonNov 28, 2025
      If your Tennant Floor Machine isn't picking up water effectively, there are several potential causes and solutions: * The recovery tank might be full; if so, drain it. * The drain hose cap could be loose; tighten it. * The float shut-off screen in the recovery tank may be clogged; clean it. * The squeegee assembly might be clogged; clean it. * The squeegee blades could be worn; replace or rotate them. * The squeegee blade deflection might be incorrect; adjust the blade height. * Vacuum hose connections may be loose; secure them. * The vacuum hose could be clogged; remove the debris. * The vacuum hose might be damaged; replace it. * The recovery tank cover might not be in place; properly position it. * The recovery tank cover seal could be damaged; replace it. * The...
  • S
    Samuel HernandezSep 18, 2025
    Why FaST system does not operate correctly on my Tennant Floor Machine?
    • C
      Christopher ArroyoSep 18, 2025
      If the FaST system on your Tennant Floor Machine isn't working correctly, first, ensure the FaST system switch is on and the FaST--PAK supply hose is connected. Check the FaST pump fuse and replace it if blown. Also, check for clogs in the FaST--PAK supply hose or connectors (soak in warm water to unclog), and ensure the FaST--PAK carton isn't empty (replace if needed). Straighten any kinks in the FaST--PAK supply hose. For other issues such as clogged solution tank filter (drain solution tank, remove solution tank filter, clean and reinstall) or clogged orifice/filter screen, or faulty components, it's best to contact a service center.
  • H
    hbarajasSep 23, 2025
    What to do if the vacuum motor will not operate on my Tennant Floor Machine?
    • R
      Renee TaylorSep 23, 2025
      If the vacuum motor on your Tennant Floor Machine isn't working, ensure the squeegee is lowered to the floor. If the vacuum motor fuse is blown, replace it with a 25 Amp fuse. For other issues, such as a faulty vacuum motor or worn motor carbon brushes, it's best to contact a service center.
  • X
    xjenkinsSep 8, 2025
    Why does my Tennant Floor Machine have little or no solution flow?
    • G
      gabriela49Sep 9, 2025
      If your Tennant Floor Machine has little or no solution flow during conventional scrubbing, it could be due to: * A clogged solution tank filter or solution hose. If this is the case, clean the filter or flush out the hose. * A clogged solution valve. If this is the case, remove the valve and clean it. * The solution flow control knob being set too low. If this is the case, adjust the knob. * A loose screw on the control knob. If this is the case, calibrate the knob and retighten the screw.
  • C
    Carolyn ThomasSep 4, 2025
    Why my Tennant Floor Machine does not propel (Drive model)?
    • J
      Julia MccoySep 5, 2025
      If your Tennant Floor Machine (Drive model) isn't propelling, replace the 30 Amp fuse. For other issues, such as a faulty relay switch, transaxle motor, or worn motor carbon brushes, it's best to contact a service center.

Summary

Machine Data Fields

Safety Precautions

Machine Installation Procedures

Installing the Batteries

Procedure for safely installing the machine's batteries.

Operating the Machine

Pre-Operation Checks

Checklist of items to verify before starting the machine.

Battery Management

Battery Meter and Fault Codes

Explanation of the battery charge indicator and fault codes.

Charging Batteries

General precautions and instructions for charging the machine's batteries.

Maintenance Procedures

Draining Tanks Procedures

Procedures for draining the machine's tanks.

Daily Maintenance

Routine maintenance tasks to perform after each use.

ec-H2 O Module Flush Procedure

Steps to flush the ec-H2O module when an alarm sounds.

Squeegee Blade Replacement

How to replace worn squeegee blades.

Transport and Storage Procedures

Troubleshooting Guide

Technical Specifications

FaST System Model Specifications

Specifications related to the FaST system for different models.

ec-H2 O System Model Specifications

Specifications related to the ec-H2O system for different models.

Machine Dimensions

Physical dimensions and diagrams of the machine.

Tennant T3 Specifications

General IconGeneral
Power SourceBattery
Sound Level68 dBA
Machine TypeWalk-Behind
Battery Voltage24 V
Cleaning Path17 in / 43 cm
Solution Tank Capacity40 L
Machine Width22 in / 56 cm

Related product manuals