Tennant T3 User Manual (English)

Other manuals for Tennant T3

Operator's Manual105 pages

Operator And Parts Manual124 pages

Use And Care Guide2 pages

Questions and Answers:

L
Lindsay SmithAug 22, 2025
Why is the brush motor on my Tennant T3 not working?
- A
  alvaradodebbieAug 22, 2025
  If the brush motor on your Tennant Scrubber isn't working, here are some possible reasons: * The scrub head may be raised off the floor: Lower the scrub head. * The battery meter lockout may be activated: Recharge the batteries. * The brush motor circuit breaker may be tripped: Reset the brush circuit breaker button. * There may be a broken or loose belt (50cm model): Replace or tighten the belt. If none of these steps work, contact a service center.
R
Rhonda CarterAug 23, 2025
How to fix a Tennant T3 that won't turn on?
- J
  Jesse BassAug 23, 2025
  If your Tennant Scrubber is not operating, there are several possible causes: * The batteries may be discharged: Charge the batteries. * The emergency-stop button may be activated: Turn the button clockwise to reset it. * There may be a loose battery cable: Tighten the loose cable. * The main fuse may be blown: Replace the fuse. * The batteries may be faulty: Replace the batteries. If none of these steps work, contact a service center.
S
Sharon GardnerAug 25, 2025
Why won't my Tennant Scrubber move?
- N
  nathan26Aug 25, 2025
  If your Tennant Scrubber isn't moving, consider the following possibilities: * The parking brake may be set: Release the parking brake lever. * The main fuse may be blown: Replace the 30 Amp fuse. If these solutions do not resolve the issue, contact a service center.
A
Anthony DelacruzAug 27, 2025
What causes the vacuum motor to fail on a Tennant T3?
- J
  Jennifer AdamsAug 27, 2025
  If the vacuum motor on your Tennant Scrubber is not working, check these potential causes: * The squeegee may be raised off the floor: Lower the squeegee. * The vacuum motor fuse may be blown: Replace the 25 Amp fuse. If these solutions do not resolve the issue, contact a service center.
C
Charles HarrisAug 27, 2025
How do I restore solution flow in my Tennant Scrubber?
- B
  Brent JimenezAug 27, 2025
  If you're experiencing little to no solution flow in your Tennant Scrubber (Conventional Scrubbing), consider the following: * The solution tank filter or solution hose may be clogged: Clean the solution tank filter or flush out the solution hose. * The solution valve may be clogged: Remove the valve and clean it. * The solution flow control knob may be set too low: Adjust the solution control flow knob. * There may be a loose screw on the control knob: Calibrate the knob and retighten the screw.
K
Kimberly CastanedaAug 30, 2025
Why my Tennant Floor Machine will not operate?
- E
  Edward LoweryAug 30, 2025
  If your Tennant Floor Machine isn't operating, consider these possible causes: * The activation bail might not be pulled; pull the activation bail. * The batteries could be discharged; charge them. * There might be faulty battery(s); replace the battery(s). * A battery cable might be loose; tighten the cable. * The main fuse could be blown; replace the fuse.
J
Jonathan WalshAug 31, 2025
What to do if the vacuum motor will not operate on Tennant Floor Machine?
- A
  Alexis SanchezAug 31, 2025
  If the vacuum motor on your Tennant Floor Machine isn't working, check the following: * Ensure the squeegee is lowered to the floor. If it's raised, lower it. * Inspect the vacuum motor fuse; if it's blown, replace it with a 25 Amp fuse.
C
Cynthia SmithSep 2, 2025
What to do if my Tennant Floor Machine will not operate?
- F
  franklintylerSep 2, 2025
  If the Tennant Floor Machine won't operate, make sure the activation bail is pulled. Other potential causes include discharged or faulty batteries (charge or replace them), a loose battery cable (tighten it), or a blown main fuse (replace it). If these steps don't resolve the issue, there may be a faulty key switch, and you should contact a service center.
M
Michael WhiteSep 3, 2025
What to do if the brush motor will not operate on my Tennant Floor Machine?
- A
  Anthony BrooksSep 3, 2025
  If the brush motor on your Tennant Floor Machine won't operate, start by ensuring the scrub head is lowered to the floor. If the battery meter lockout is activated, recharge the batteries. Check if the brush motor circuit breaker has tripped and reset it if necessary. For other issues such as faulty switches, motor, or worn carbon brushes, it's best to contact a service center.
C
Carolyn ThomasSep 4, 2025
Why my Tennant Floor Machine does not propel (Drive model)?
- J
  Julia MccoySep 5, 2025
  If your Tennant Floor Machine (Drive model) isn't propelling, replace the 30 Amp fuse. For other issues, such as a faulty relay switch, transaxle motor, or worn motor carbon brushes, it's best to contact a service center.

Tennant T3 Specifications

General

Power Source	Battery
Sound Level	68 dBA
Machine Type	Walk-Behind
Battery Voltage	24 V
Cleaning Path	17 in / 43 cm
Solution Tank Capacity	40 L
Machine Width	22 in / 56 cm