How to troubleshoot poor scrubbing performance on a Tennant Scrubber?
If your Tennant Scrubber has poor scrubbing performance, start by removing any debris caught in the brush. If the brushes/pads are worn, replace them. Also, ensure that you are using the correct brush/pad type and adjust the pressure setting accordingly.
Why won't my Tennant T5 operate?
If your Tennant Scrubber won't operate, several issues could be the cause. First, ensure the batteries are charged. If the emergency-stop button is activated, turn it clockwise to reset it. Check for loose battery cables and tighten them if necessary. Faulty batteries may also be the reason, so consider replacing them.
Why Tennant T5 machine will not propel?
The Tennant Scrubber may fail to propel if the parking brake is set. Release the parking brake lever to resolve this. Also, avoid steep inclines and reset the key if you have exceeded the maximum incline.
How to fix onboard battery charger if it will not operate on Tennant T5?
If the onboard battery charger of your Tennant Scrubber isn't working, check if the plug is properly connected to the power supply. If not, ensure a proper connection. Also, replace the charger fuse if it's faulty, or replace the power supply cord if it's faulty.
How to improve water pickup on Tennant Scrubber?
If your Tennant Scrubber isn't picking up water effectively, start by draining the recovery tank, as it might be full or have excessive foam buildup. Check for a loose drain hose cap and tighten it. Clean the float shut-off screen located in the recovery tank, as well as the squeegee assembly. Inspect the squeegee blades for wear and replace or rotate them if needed. Adjust the squeegee blade height if the deflection is incorrect. Ensure all vacuum hose connections are secure and that the vacuum hose isn't clogged or damaged. Verify the recovery tank cover is properly positioned and the seal isn't damaged, replacing if necessary.
Why is my Tennant Floor Machine not picking up water?
If your Tennant Floor Machine isn't picking up water well, several factors could be at play. First, the recovery tank might be full or have too much foam; in this case, drain the recovery tank. A loose drain hose cap could also be the culprit; make sure to tighten it. Check for any clogs in the float shut-off screen inside the recovery tank and clean it if necessary. The squeegee assembly might also be clogged, so give that a thorough cleaning. Inspect the squeegee blades for wear and either replace or rotate them. Ensure the squeegee blade height is correctly adjusted. Loose vacuum hose connections can also cause poor pickup, so ensure they are secure. Clear out any debris from a clogged vacuum hose, and if the hose is damaged, replace it. Finally, make sure the recovery tank cover is pro...
Why does my Tennant Floor Machine have reduced run time?
If you're experiencing reduced run time with your Tennant Floor Machine, the first thing to check is whether the batteries are fully charged; if not, fully recharge them. If the issue persists, the batteries might be defective and need replacement. Also, ensure that the batteries receive proper maintenance. If the battery charger is faulty, consider repairing or replacing it.
Why are solution flow and brush pressure buttons locked on my Tennant Floor Machine?
If the solution flow and brush pressure buttons, along with the FaST system switch, are locked on your Tennant Floor Machine, it's likely that the supervisor controls (lock-out feature) have been activated. Please contact your supervisor.
Why won't the vacuum motor operate on my Tennant T5 Scrubber?
If the vacuum motor on your Tennant Scrubber won't operate, make sure the squeegee is lowered to the floor. Also, ensure the batteries are charged.
Why does my Tennant T5 Scrubber not propel?
If your Tennant Scrubber won't propel, first check if the parking brake is set and release it. Also, avoid steep inclines and reset the key if you have exceeded the maximum incline.
Covers essential safety rules for operating and servicing the machine.
Specific safety guidelines for loading and unloading the machine onto vehicles.
Procedure for correctly installing the batteries into the machine.
Checklist of essential tasks before starting the machine.
How to adjust speed, brush pressure, and solution flow.
General| Power Source | Battery |
|---|---|
| Sound Level | 67 dBA |
| Machine Type | Walk-Behind Scrubber |
| Battery Voltage | 24 V |
| Machine Width | 24 in / 61 cm |
To Next Page
