Tennant T260 - User Manual

Questions and Answers

M
Makayla MartinezAug 17, 2025
What to do if the brush plate motor does not work on my Tennant Scrubber?
- D
  Darrell JohnsonAug 17, 2025
  If the brush plate motor on your Tennant Scrubber isn't working, there could be several reasons. The brush plate may be raised from the ground, or the brush plate motor button might be damaged; in this case, replace the micro switch of the brush plate motor. A damaged motor switch could also be the issue, requiring replacement of the motor micro switch. Additionally, the overload reset switch might have tripped; troubleshoot and press the overload reset switch to resolve this. The brush plate motor itself might be damaged, requiring you to replace the motor.
A
Alison HollandAug 19, 2025
Why the suction motor does not work on my Tennant T260 Scrubber?
- S
  Stephen TownsendAug 20, 2025
  If the suction motor on your Tennant Scrubber isn't working, there are several potential causes. The micro switch at the lifting pedal of the squeegee might be damaged, requiring replacement. The motor inching button could also be damaged, necessitating replacement of the micro switch. The suction motor itself might be damaged, requiring replacement. Other causes could be: the recovery tank is full, so drain the water; the filter screen of solution tank is dirty, so clean the filter screen; the water valve switch is broken, so replace it; the solenoid valve is broken, so replace solenoid valve.
Q
qcookAug 22, 2025
What to do if brush plate motor does not work on Tennant Scrubber?
- J
  Julie BowersAug 22, 2025
  If the brush plate motor on your Tennant Scrubber isn't working, several things could be wrong. A common cause is the brush plate rising from the ground or a damaged brush plate motor button; in this case, replace the micro switch of the brush plate motor. A damaged motor switch can also be the culprit, requiring replacement of the motor micro switch. Additionally, check for a tripped overload reset switch and, if necessary, troubleshoot and press the reset switch. Finally, make sure the brush plate motor connector is securely fixed. If none of these solutions work, the motor itself may be damaged and need replacement.
D
donald96Aug 26, 2025
What to do if the suction motor does not work on Tennant Scrubber?
- B
  Brian ChambersAug 26, 2025
  If the suction motor on your Tennant Scrubber isn't working, there are several potential causes. It could be due to a damaged micro switch at the lifting pedal of the squeegee, which would require replacing the micro switch. Another possibility is a disconnected micro switch wire, which you should reinsert. A damaged motor inching button can also cause this issue, necessitating replacement of the micro switch. In some cases, the suction motor itself may be damaged and need replacement. Also, ensure the recovery tank is not full; if it is, drain the sewage.
R
Robert PatrickAug 28, 2025
How to fix a Tennant T260 charger that is not working?
- H
  Hannah WhiteAug 28, 2025
  If your Tennant Scrubber charger isn't working, start by checking the plug connection to the power supply. Ensure it's properly connected. Also, verify the correct connection of the positive and negative wires. If these steps don't resolve the issue, the charger itself may be faulty, and you should refer to the charger fault code for further troubleshooting.
R
Robert PerezAug 30, 2025
What to do if my Tennant Scrubber machine cannot advance?
- R
  Ronald DunlapAug 30, 2025
  If your Tennant Scrubber isn't advancing, it might be due to universal wheel damage, so replace the universal wheel. Another reason might be large caster damage, so replace the damaged large caster. The brush plate angle may be incorrect, so re-adjust the brush plate angle.
L
Laura DavenportSep 2, 2025
Why is the charger not working on my Tennant T260?
- J
  johnmcclainSep 2, 2025
  If your Tennant Scrubber's charger isn't working, start by checking the plug connection to the power supply. Also, verify the positive and negative wires are correctly connected. If those aren't the issue, refer to the charger fault code for further troubleshooting.
E
Elizabeth ScottSep 5, 2025
Why the Tennant T260 Scrubber cannot advance?
- L
  lovenancySep 5, 2025
  If your Tennant Scrubber isn't advancing, it might be due to universal wheel damage, which requires replacing the universal wheel. Another cause could be damaged large casters, which should also be replaced. Finally, the brush plate angle could be incorrect and needs re-adjusting.
H
houstonmitchellSep 7, 2025
What to do if Tennant T260 Scrubber has little water or no water outflow?
- G
  Gina RomeroSep 8, 2025
  If your Tennant Scrubber has little to no water outflow, first check the filter screen of the solution tank and clean it if necessary. If that doesn't solve the problem, the water valve switch may be broken and need replacement. Another potential issue is a malfunctioning solenoid valve, which would also need replacement. Additionally, impurities in the solenoid valve can cause this issue. To resolve this, fill up the solution tank, open the water valve to the maximum, and start the machine to flush out the impurities. Repeat this process several times.
B
Brandon HallSep 12, 2025
Why my Tennant T260 Scrubber machine cannot be operated?
- R
  rodgerselizabethSep 12, 2025
  If your Tennant Scrubber won't operate, several factors could be at play. It might be due to a faulty or disabled switch. Try turning on the switch or replacing it if necessary. Another potential cause is a problem with the brush plate motor button; in this case, turn on the switch or replace it. A malfunctioning motor switch handle could also be the culprit, requiring replacement of the micro switch. Alternatively, the battery might be dead or damaged, necessitating charging or replacement. Lastly, an overload reset switch tripped could be the reason. To resolve this, remove the short circuit fault and press the overload reset switch.

Summary

Protect the Environment

Machine Data

Safety Precautions

General Safety Warnings

Warnings about hazards and unsafe practices.

Safe Operation Guidelines

Actions and conditions for safe machine operation.

Operational Safety Procedures

Pre-Operation and Usage Safety

Safety checks before starting and during machine operation.

Post-Operation and Servicing Safety

Safety measures before leaving or servicing the machine.

Loading and Unloading Safety

Intended Use

Security Label Information

T260 Machine Components

Operation Panel and Controls

Machine Installation Overview

Unpacking the Machine

Steps for checking and unpacking the machine from its packaging.

Battery Installation Procedure

How the Machine Works

Brush and Scouring Pad Information

Connect Squeegee Assembly

Install the Brush Plate

Pour Solution Into Tank

Machine Operation Basics

Check Before Operation

Pre-operational checks for safety and machine readiness.

Start the Machine

Steps to power on and begin machine operation.

Operating Procedures

Squeegee and Suction Operation

Lowering the squeegee and engaging the water suction motor.

Water Flow and Cleaning Start

Adjusting water output and starting the cleaning process.

Stopping Machine Operation

Procedure to safely stop the machine and its components.

During Machine Operation

Battery Meter and Indicators

Overload Reset Switch

Timer and Hour Meter

Water Tank Drainage

Discharge Recovery Tank

Procedure for draining and cleaning the recovery tank.

Clean Collection Basket

Instructions for disassembling and flushing the debris collection basket.

Drain Solution Tank

Battery Charging

Battery Charger Use

Battery Installation and Use Precautions

Battery Charging Details

Battery Storage and Temperature

Guidelines for storing batteries and managing temperature effects.

LED Indicator Status

Understanding the LED indicators for the smart battery charger.

Machine Maintenance

Daily Maintenance Tasks

Procedures for daily cleaning and maintenance.

Component Maintenance

Clean and Inspect Squeegee Blade

Cleaning the squeegee blade and checking for wear.

Wipe Down Machine

General cleaning of the machine exterior with a damp cloth.

Weekly Maintenance

Clean Solution Tank Filter Screen

Procedure to clean the filter screen of the solution tank.

Clean Battery Terminals

Cleaning battery tops to prevent corrosion and checking wiring.

Maintenance Schedule Table

Squeegee Blade Replacement

Moving the Machine

Store the Machine

Antifreeze Procedure

Troubleshooting Common Problems

Troubleshooting Specific Issues

Troubleshooting Insufficient Suction

Solutions for problems related to weak or no suction.

Troubleshooting Reduced Operating Time

Solutions for issues causing reduced machine operating time.

Battery Charger Fault Codes

Specifications

General Machine Size and Capacity

Physical dimensions and tank capacities of the machine.

Machine Type Specifications

Details on battery, electric motor, and charger types.

Machine Dimensions Diagram

Product Warranty Information

Tennant T260 Specifications

General

Model	T260
Type	Walk-Behind Scrubber
Sound Level	68 dBA
Brush Down Pressure	Up to 100 lbs
Battery Voltage	24 V
Cleaning Path Width	20 in
Cleaning Path	20 in
Brush Motor	0.75 hp
Length	46 in / 1170 mm
Width	22 in
Height	40 in
Dimensions	L x W x H: 46 in x 21 in x 41 in / 1170 mm x 530 mm x 1040 mm